RESUMO

PURPOSE: To evaluate the influence of different post-endodontic techniques on the fatigue survival and biomechanical behavior of crowned restored central incisors. METHODS: The crowns of 69 bovine incisors were cut, and the roots were treated endodontically and assigned randomly into three groups (n=23): resin composite buildup (BUP), glass fiber post-retained resin composite buildup (GFP), and cast post-and-core (CPC). They received full crown preparation with 2 mm ferrule, and a leucite-reinforced ceramic crown was cemented adhesively. Three specimens from each group were tested monotonically. The remaining specimens were subjected to the stepwise stress fatigue test until fracture or suspension after 1.5 x 106 cycles in a chewing simulator. The load and step at which each specimen failed were analyzed by Kaplan-Meier and Mantel-Cox (log-rank test) statistics, followed by multiple pairwise comparisons, at 5% significance level. The three groups tested (BUP, GFP, and CPC) were 3D modeled (Rhinoceros 4.0) and the maximum principal stress (MPa) criteria were used to calculate the results using FEA. RESULTS: There was no statistical difference between the treatments regarding the load or the number of cycles (Mantel-Cox log-rank test for trend, X²= 0.015, df=1, P= 0.901, X²=3.171, df=1, P= 0.995). Crown cracks were the predominant failure mode, and oblique root fractures were only observed in groups GFP and CPC. In endodontically treated incisors with a 2-mm ferrule, the post-endodontic treatment had no significant effect on fatigue survival. Non-restorable fractures only occurred in teeth restored with posts. CLINICAL SIGNIFICANCE: Although the clinical significance of laboratory studies has some limitations, this study suggests that composite buildups without posts may be an option for restoring endodontically treated incisors with 2 mm ferrule height.

Assuntos

RESUMO

Different techniques are available to manufacture polymer-infiltrated ceramic restorations cemented on a chairside titanium base. To compare the influence of these techniques in the mechanical response, 75 implant-supported crowns were divided in three groups: CME (crown cemented on a mesostructure), a two-piece prosthetic solution consisting of a crown and hybrid abutment; MC (monolithic crown), a one-piece prosthetic solution consisting of a crown; and MP (monolithic crown with perforation), a one-piece prosthetic solution consisting of a crown with a screw access hole. All specimens were stepwise fatigued (50 N in each 20,000 cycles until 1200 N and 350,000 cycles). The failed crowns were inspected under scanning electron microscopy. The finite element method was applied to analyze mechanical behavior under 300 N axial load. Log-Rank (p = 0.17) and Wilcoxon (p = 0.11) tests revealed similar survival probability at 300 and 900 N. Higher stress concentration was observed in the crowns' emergence profiles. The MP and CME techniques showed similar survival and can be applied to manufacture an implant-supported crown. In all groups, the stress concentration associated with fractographic analysis suggests that the region of the emergence profile should always be evaluated due to the high prevalence of failures in this area.

RESUMO

OBJECTIVE: To determine whether the thickness, processing technique, and cooling protocol of veneer ceramic influence the flexural strength of a bilayer ceramic system. MATERIALS AND METHODS: Sixty-four bar-shaped specimens (20mm×4mm×1mm) of yttria-stabilized tetragonal zirconia (Vita In-Ceram YZ, Vita) were fabricated (ISO 6872) and randomly divided into 8 groups (n=8) according to the factors "processing technique" (P - PM9 and V - VM9), "thickness" (1mm and 3mm), and "cooling protocol" (S - slow and F - fast). The veneer ceramics were applied only over one side of the bar-shaped specimens. All specimens were mechanically cycled (2×10(6) cycles, 84N, 3.4Hz, in water), with the veneer ceramic under tension. Then, the specimens were tested in 4-point bending (1mm/min, load 100kgf, in water), also with the veneer ceramic under tension, and the maximum load was recorded at first sign of fracture. The flexural strength (σ) was calculated, and the mode of failure was determined by stereomicroscopy (30×). The data (MPa) were analyzed statistically by 3-way ANOVA and Tukey's test (α=0.05). RESULTS: ANOVA revealed that the factor "thickness" (p=0.0001) was statistically significant, unlike the factors "processing technique" (p=0.6025) and "cooling protocol" (p=0.4199). The predominant mode of failure was cracking. SIGNIFICANCE: The thickness of the veneer ceramic has an influence on the mechanical strength of the bilayer ceramic system, regardless of processing technique and cooling protocol of the veneer ceramic.

Assuntos