RESUMO

The aim of this study was to evaluate whether the compressive strength of lithium dissilicate ceramic inlays is influenced by the substrate (dentin or composite resin build-up) and to compare it to nonrestored teeth. Thirty freshly extracted human maxillary third molars were selected and randomly ascribed to three groups (n=10). Standardized Class II MOD preparations were made (bucco-palatal width = 2/3 of the intercuspal width and 2/3 of the width at the tooth equator for the proximal boxes), varying the extension of the preparations (Group 2: preparation limited to tooth structure; Group 3: pulpal floor of the preparation rebuilt with composite resin, IPS Empress Direct, restored with lithium dissilicate CAD/CAM ceramic inlays (e.max CAD) and cemented with a resin cement (Variolink II)). All groups were subjected to compressive strength test (1mm/min crosshead speed). The results showed that the fracture strength of G1 (control group) was significantly higher than G2 and G3, while within these groups there were no statistically significant differences. Both groups restored with lithium dissilicate restorations did not reach the fracture strength of the sound teeth but were statistically equivalent and sufficient to withstand physiologic masticatory forces.

RESUMO

CONTEXT: Studies have been conducted to measure the fracture resistance of restored teeth with the current restorative materials. However, most of those studies disregard the cavity size as an influencing variable. AIMS: To evaluate the fracture resistance of prepared and restored maxillary premolars with medium and large preparations. MATERIALS AND METHODS: Seventy superior and sound premolars were randomly divided: G1 (control) - sound tooth; G2, G3, and G4 received a Class II mesial-occlusal-distal (MOD) preparation with an occlusal box width 1/3 of the intercuspal distance, and were restored with Filtek Z350 XT, IPS Empress Direct, and Charisma Diamond, respectively; G5, G6, and G7 received a Class II MOD preparation with an occlusal box width 2/3 of the intercuspal distance, and were restored with Filtek Z350 XT, IPS Empress Direct, and Charisma Diamond, respectively. After storage in water, at 37°C, the specimens were subjected to a fracture test under compression in a universal testing machine where the loads were applied vertically and at a speed of 0.5 mm/min. STATISTICAL ANALYSIS USED: Data were analyzed with two-way ANOVA and Tukey's multiple comparison post hoc test (P < 0.05). RESULTS: G1 presented a fracture resistance significantly higher (P = 0.005) than any other experimental groups. Among the experimental groups, only G5 showed a significantly low fracture resistance (P = 0.019) when compared to the other groups. For the other resins, the change in intercuspal distance from 1/3 to 2/3 the intercuspal distance did not significantly reduce the fracture resistance (P > 0.05). CONCLUSIONS: The cavity preparation weakens the remaining tooth structure; however, its resistance could be partially restored using direct adhesive restorations.

Assuntos

RESUMO

OBJECTIVE: This study aimed to evaluate the ability of the proposed technique in producing restorations that exhibit mimesis with tooth structure and to define a restorative clinical protocol. MATERIALS AND METHODS: For this study a typodont was used. The right upper central incisor with Class IV lesion was restored with the layering technique (reference tooth, RT). For the left upper central incisor with Class IV lesion, six teeth were restored monochromatically (test teeth, TT), using DA3.5 (n = 3) and DA4 (n = 3) composite resins-resulting in six unsatisfactory color restorations. TT were divided into six groups depending on the color of unsatisfactory restoration and preparation depth. First, a preparation was realized on the labial surface with 0.5 mm, 0.7 mm or 1.0 mm of depth. A second preparation was then performed to reproduce the dentinal mamelons. Next, adhesive procedures were performed and the teeth restored. Opaque halo, opalescent halo and vestibular enamel were then reproduced by the addition of different composite resins. The RT and TT were photographed side by side in typodont to obtain six photographic prints. The photographs of the groups were subjected to visual evaluation by 120 volunteers via a questionnaire. Data were analyzed by the prevalence of answers, and Chi-square test was used to investigate the association between variables at .05 significance. Furthermore, ΔE of groups was evaluated in comparison RT. RESULTS: The results demonstrated that the moderate intensity restorations (DA3.5) with depths of 0.5 mm and 0.7 mm had the highest prevalence of acceptance. For severe intensity restorations (DA4), the preparation depth of 1.0 mm obtained better acceptance. CONCLUSIONS: The technique was able to modify the final color of Class IV restorations, producing satisfactory color restorations. CLINICAL SIGNIFICANCE: This technique can be used for color correction in cases of Class IV restorations, in situations where there is no time for immediate layered restoration, and as a restorative technique.

Assuntos

RESUMO

The polishing step of teeth preparations for crowns is a step often performed, so that there is an increased time during the clinical procedure. The aim of this study is to evaluate the marginal and internal adaptation of all-ceramic CAD/CAM lithium disilicate crowns in polished preparations for crown and nonpolished preparations for crowns. For this purpose, 20 first molars were selected, which were divided into two groups (n = 10) G1, teeth that received surface roughening similar to preparation without polishing, and G2 (control), polished preparations. After the preparations were completed the teeth were scanned (Cerec Bluecam, Sirona, Bensheim, Germany), and the crowns were designed and machined using CAD/CAM technology (Sirona, Bensheim, Germany). The adaptation of the pieces was evaluated using polyvinyl siloxane replicas and stereomicroscope photographs with 70x magnifications. The normality test indicated a nonnormal result, so a Man-Whitney nonparametric test was performed. One out of the 24 measured regions showed a statistically significant difference (p = 0.0494). With this study it can be concluded that crowns fabricated by CAD/CAM technology performed on unpolished preparations are not influenced by the internal marginal adaptation and the ceramic part and are different from polished preparations.

RESUMO

Introduction: The development and validation of mathematical models is an important step of the methodology of finite element studies. Objective: This study aims to describe the development and validation of a three-dimensional numerical model of a maxillary premolar for finite element analysis. Material and method: The 3D model was based on standardized photographs of sequential slices of an intact premolar and generated with the use of SolidWorks Software (Dassault, France). In order to validate the model, compression and numerical tests were performed. The load versus displacement graphs of both tests were visually compared, the percentage of error calculated and homogeneity of regression coefficients tested. Result: An accurate 3D model was developed and validated since the graphs were visually similar, the percentage error was within acceptable limits, and the straight lines were considered parallel. Conclusion: The modeling procedures and validation described allows the development of accurate 3D dental models with biomechanical behavior similar to natural teeth. The methods may be applied in development and validation of new models and computer-aided simulations using FEM.

Introdução: O desenvolvimento e validação de modelos matemáticos é uma importante etapa da metodologia de estudos de elementos finitos. Objetivo: Este estudo tem o objetivo descrever o desenvolvimento e validação de um modelo numérico tridimensional de um pré-molar superior para análise em elementos finitos. Material e método: Fotografias padronizadas de cortes sequenciais de um pré-molar hígido serviram de referência para o desenvolvimento do modelo 3D, que foi construído por meio do programa SolidWorks (Dassault, França). A fim de validar o modelo testes de compressão e simulação numérica foram realizados. Os gráficos de carga versus deslocamento de ambos os ensaios foram comparados visualmente, a percentagem de erro calculada e homogeneidade dos coeficientes de regressão testada. Resultado: Um modelo 3D preciso foi desenvolvido e validado, uma vez que os gráficos apresentavam-se visualmente semelhantes, o percentual de erro ficou dentro dos limites aceitáveis e as retas foram consideradas paralelas. Conclusão: Os procedimentos de modelagem e validação descritos permitem o desenvolvimento de modelos dentários 3D precisos com comportamento biomecânico semelhante aos dentes naturais. Os métodos podem ser aplicados no desenvolvimento e validação de novos modelos e estudos de simulações computacionais por meio do MEF.

Assuntos

RESUMO

Desde a introdução do primeiro sistema bem-sucedido de cerâmica fundida a metal, há uma crescente demanda de restaurações cerâmicas, pois se trata de um material de grande propriedade estética, devido à disponibilidade de uma ampla gama de matizes e efeitos de translucidez. O desenvolvimento das cerâmicas levou a uma gama maior de indicações e transformou o desenho dos preparos clássicos de facetas em desenhos estendidos e orientados pelo defeito prévio do remanescente dental, as chamadas “facetas estendidas”. No entanto, mesmo que atualmente as facetas clássicas e estendidas possam ser soluções alternativas aos preparos para coroa total, elas não devem ser sempre a primeira escolha para todas as situações clínicas, porque vários fatores devem ser considerados antes da elaboração de um plano de tratamento. Portanto, fazer a escolha certa entre coroas, facetas clássicas e estendidas na dentição anterior para cada situação clínica é elemento-chave para um tratamento conservador e longevo. Neste artigo uma classificação de acordo com o conteúdo das cerâmicas odontológicas é descrita, e são abordadas importantes considerações baseadas em evidência, relacionadas ao plano de tratamento de reabilitações nos dentes anteriores com coroas e facetas cerâmicas...

Since the introduction of the first porcelain-fused-to-metal system, there has been a growing demand for ceramic restorations, since it is a material that provides good aesthetics, wide range of shades and translucency effects. The development of new reinforced ceramics has led to a broader range of indications and changed the conventional veneer preparations into extended defect-oriented preparation designs, the so called “extended veneers”. However, even though classical and extended veneers can be an alternative to full crown preparations, they should not always be the first choice for every clinical situations because several factors must be taken into consideration before elaborating a treatment planning. Therefore, making the right choice between all-ceramic crowns, conventional and extended veneers in the anterior dentition is key for a conservative and long-lasting treatment for each individual situation. This article describes a classification of the ceramic systems, addressing important evidence-based considerations regarding the treatment planning rehabilitation of the anterior dentition using all-ceramic crowns and veneers...

Assuntos

RESUMO

The purpose of this study was to determine the effect of cavity depth, ceramic thickness, and resin bases with different elastic modulus on von Mises stress patterns of ceramic inlays. Tridimensional geometric models were developed with SolidWorks image software. The differences between the models were: depth of pulpal wall, ceramic thickness, and presence of composite bases with different thickness and elastic modulus. The geometric models were constrained at the proximal surfaces and base of maxillary bone. A load of 100 N was applied. The stress distribution pattern was analyzed with von Mises stress diagrams. The maximum von Mises stress values ranged from 176 MPa to 263 MPa and varied among the 3D-models. The highest von Mises stress value was found on models with 1-mm-thick composite resin base and 1-mm-thick ceramic inlay. Intermediate values (249-250 MPa) occurred on models with 2-mm-thick composite resin base and 1-mm-thick ceramic inlay and 1-mm-thick composite resin base and 2-mm-thick ceramic inlay. The lowest values were observed on models restored exclusively with ceramic inlay (176 MPa to 182 MPa). It was found that thicker inlays distribute stress more favorably and bases with low elastic modulus increase stress concentrations on the internal surface of the ceramic inlay. The increase of ceramic thickness tends to present more favorable stress distribution, especially when bonded directly onto the cavity without the use of supporting materials. When the use of a composite base is required, composite resin with high elastic modulus and reduced thickness should be preferred.

Assuntos

RESUMO

The purpose of this study was to determine the effect of cavity depth, ceramic thickness, and resin bases with different elastic modulus on von Mises stress patterns of ceramic inlays. Tridimensional geometric models were developed with SolidWorks image software. The differences between the models were: depth of pulpal wall, ceramic thickness, and presence of composite bases with different thickness and elastic modulus. The geometric models were constrained at the proximal surfaces and base of maxillary bone. A load of 100 N was applied. The stress distribution pattern was analyzed with von Mises stress diagrams. The maximum von Mises stress values ranged from 176 MPa to 263 MPa and varied among the 3D-models. The highest von Mises stress value was found on models with 1-mm-thick composite resin base and 1-mm-thick ceramic inlay. Intermediate values (249-250 MPa) occurred on models with 2-mm-thick composite resin base and 1-mm-thick ceramic inlay and 1-mm-thick composite resin base and 2-mm-thick ceramic inlay. The lowest values were observed on models restored exclusively with ceramic inlay (176 MPa to 182 MPa). It was found that thicker inlays distribute stress more favorably and bases with low elastic modulus increase stress concentrations on the internal surface of the ceramic inlay. The increase of ceramic thickness tends to present more favorable stress distribution, especially when bonded directly onto the cavity without the use of supporting materials. When the use of a composite base is required, composite resin with high elastic modulus and reduced thickness should be preferred.

O objetivo do estudo foi avaliar o efeito da profundidade da cavidade, da espessura da cerâmica e da presença de bases de resina, com os diferentes módulos de elasticidade na distribuição de tensões de von Mises em inlays cerâmicos. Modelos geométricos tridimensionais foram desenvolvidos com o software SolidWorks. As diferenças entre os modelos foram: a profundidade da parede pulpar, a espessura da cerâmica e a presença de bases de resina composta com diferentes espessuras e módulos de elasticidade. Os modelos geométricos foram engastados nas superfícies proximais e base do osso maxilar e uma carga de 100 Newton foi aplicada. O padrão de distribuição de tensões foi analisado com diagramas de tensão de von Mises. O valor de tensão máxima de von Mises foi variável entre os modelos e situou-se na faixa entre 176 e 263 MPa. O maior valor foi encontrado nos modelos restaurados com bases de resina composta de 1 mm e inlay cerâmico de 1 mm de espessura. Valores intermediários (249-250 MPa) ocorreram nos modelos com bases de resina composta de 2 mm e inlays de 1 mm de espessura e nos modelos com bases de resina composta de 1 mm e inlays de 2 mm. Os menores valores foram observados nos modelos restaurados exclusivamente com inlay cerâmico (176-182 MPa). Verificou-se que inlays com maior espessura distribuem o estresse de forma mais favorável e bases com baixo módulo de elasticidade aumentam a concentração de tensões na superfície interna do inlay de cerâmica. O aumento da espessura do material cerâmico tende a apresentar uma distribuição de tensões mais favorável, principalmente quando cimentadas diretamente sobre o preparo cavitário, sem a existência de materiais intermediários. Em situações em que o emprego de materiais de base é necessária, deve-se preferir resinas compostas com alto módulo de elasticidade e espessura reduzida.

Assuntos

RESUMO

AIM: The aim of this study was to evaluate the influence of the subject's age and dentin etching time on the clinical performance of a two-step etch-and-rinse adhesive in class V non-carious cervical lesions (NCCLs). MATERIALS AND METHODS: Forty patients with NCCLs (classified as degrees 2 and 3 of dentin sclerosis) were enrolled in this study. The lesions were selected and assigned into two groups (n = 70/group) according to the subject's age: (G1) between 21-35 years old and (G2) between 40-54 years old. Each group was randomly divided into two subgroups (n = 35/group) according to dentin etching time using recommended application time (15 s) and an extended application time (30 s). A total of 140 restorations with XP Bond (Dentsply DeTrey, Germany) were placed. The composite resin Esthet X (Dentsply) was placed incrementally. All restorations were evaluated using the modified USPHS criteria. Data was analyzed by the McNemar and chi-square tests (p < 0.05). RESULTS: At the end of 2 years, 132 restorations (94.2% recall rate) were evaluated. The 24-month retention rates (%) were 93.5 for G1(15), 97.1 for G1(30), 93.9 for G2(15), and 97.0 for G2(30). There were no statistical differences in the retention rates in each recall period among groups. CONCLUSION: For the selected age groups, neither the subject's age nor the etching time had any influence on the clinical performance of XP Bond adhesive in NCCLs over a 24-month period. CLINICAL RELEVANCE: The clinical effectiveness of the XP Bond was excellent after 2 years of clinical service. Long-term clinical evaluations are necessary to confirm this finding.

Assuntos

RESUMO

A óbvia diferença estrutural entre o esmalte humano e os materiais restauradores estéticos explica a alta dificuldade de emulação da cor dental, pois esses se relacionam com a luz natural de maneiras extremamente distintas. O esmalte dental, quando iluminado, produz efeitos ópticos baseados nos princípios de birrefringência. Esse tecido interage com a luz e a decompõe em distintos feixes de diferentes comprimentos de onda, o que gera mudanças dinâmicas de cor, dependendo do ângulo de incidência da luz e de sua trajetória dentro do corpo prismático tridimensional do esmalte. Nesse sentido, é necessário estudar os meios para explorar e entender melhor como os dentes naturais têm suas expressões cromáticas estabelecidas. Neste segundo artigo sobre dupla polarização da luz, a metodologia necessária para a produção dessa técnica de extração e registro dos variados efeitos ópticos do esmalte é descrita.

The obvious structural difference between human enamel and the esthetic restorative materials explains the high complexity in achieving shade matching and color reproduction, since such substrates interact with natural light through highly different ways. Enamel yields optical effects based on principles of birefringence when illuminated. The tissue decomposes light into distinct rays and wavelengths which produces dynamic hue changes depending on the light incidence angle and on its trajectory within the tridimensional prismatic enamel body. Accordingly, it is necessary further studies on the interrelation between teeth and light, in order to better explore and understand how the chromatic expressions of natural teeth are set. The aim of this second paper on double light polarization was to describe the methodology required to carry out this technique of obtaining and recording the multiple optical effects of natural teeth.

Assuntos