RESUMO

Biopolymers such as carboxymethyl cellulose and hyaluronic acid are alternative substrates for conformable organic light-emitting diodes (OLEDs). However, drawbacks such as mechanical stress susceptibility can hinder the device's performance under stretched conditions. To overcome these limitations, herein, we developed a nanocomposite based on CMC/HA (carboxymethyl cellulose/hyaluronic acid) and synthetic Laponite, intending to improve the mechanical strength without compromising the film flexibility and transparency (transmittance >80%; 380-700 nm) as substrates for conformable OLEDs. From XRD, FTIR, CP-MAS NMR, and TGA/DTG characterization techniques, it was possible to conclude the presence of Laponite randomly dispersed between the polymer chains. CMC/HA with 5% (w/w) Laponite, CMC/HA 5, presented a higher tensile strength (370.6 MPa) and comparable Young's modulus (51.0 ± 1.2 MPa) in comparison to the nanocomposites and pristine films, indicating a better candidate for the device's substrates. To produce the OLED, the multilayer structure ITO/MoO3/NPB/TCTA:Ir(ppy)3/TPBi:Ir(ppy)3/BPhen/LiF was deposited onto the CMC/HA 5 substrate. The OLEDs fabricated using CMC/HA 5 substrates showed higher luminance (12 kcd/m2) and irradiance (0.9 mW/cm2) values when compared with those based on commercial bacterial cellulose. However, the same device presented a lower efficiency (3.2 cd/A) due to a higher current density. Moreover, the OLED fabricated onto the Laponite-modified biopolymer presented reproducible behavior when submitted to continuous bending stress. Thus, CMC/HA 5 demonstrates potential as a transparent conductor substrate for biopolymer-based OLEDs with comparable performance to commercial bacterial cellulose features.

RESUMO

Leishmaniasis, caused by Leishmania parasites, is a neglected tropical disease and Cutaneous Leishmaniasis (CL) is the most common form. Despite the associated toxicity and adverse effects, Meglumine antimoniate (MA) remains the first-choice treatment for CL in Brazil, pressing the need for the development of better alternatives. Bacterial NanoCellulose (BNC), a biocompatible nanomaterial, has unique properties regarding wound healing. In a previous study, we showed that use of topical BNC + systemic MA significantly increased the cure rate of CL patients, compared to treatment with MA alone. Herein, we performed a study comparing the combination of a wound dressing (BNC or placebo) plus systemic MA versus systemic MA alone, in CL caused by Leishmania braziliensis. We show that patients treated with the combination treatment (BNC or placebo) + MA showed improved cure rates and decreased need for rescue treatment, although differences compared to controls (systemic MA alone) were not significant. However, the overall time-to-cure was significantly lower in groups treated with the combination treatment (BNC+ systemic MA or placebo + systemic MA) in comparison to controls (MA alone), indicating that the use of a wound dressing improves CL treatment outcome. Assessment of the immune response in peripheral blood showed an overall downmodulation in the inflammatory landscape and a significant decrease in the production of IL-1a (p < 0.05) in patients treated with topical BNC + systemic MA. Our results show that the application of wound dressings to CL lesions can improve chemotherapy outcome in CL caused by L. braziliensis.

RESUMO

In this work, scaffolds based on poly(hydroxybutyrate) (PHB) and micronized bacterial cellulose (BC) were produced through 3D printing. Filaments for the printing were obtained by varying the percentage of micronized BC (0.25, 0.50, 1.00, and 2.00%) inserted in relation to the PHB matrix. Despite the varying concentrations of BC, the biocomposite filaments predominantly contained PHB functional groups, as Fourier transform infrared spectroscopy (FTIR) demonstrated. Thermogravimetric analyses (i.e., TG and DTG) of the filaments showed that the peak temperature (Tpeak) of PHB degradation decreased as the concentration of BC increased, with the lowest being 248 °C, referring to the biocomposite filament PHB/2.0% BC, which has the highest concentration of BC. Although there was a variation in the thermal behavior of the filaments, it was not significant enough to make printing impossible, considering that the PHB melting temperature was 170 °C. Biological assays indicated the non-cytotoxicity of scaffolds and the provision of cell anchorage sites. The results obtained in this research open up new paths for the application of this innovation in tissue engineering.

RESUMO

We review the recent progress that have led to the development of porous materials based on cellulose nanostructures found in plants and other resources. In light of the properties that emerge from the chemistry, shape and structural control, we discuss some of the most promising uses of a plant-based material, nanocellulose, in regenerative medicine. Following a brief discussion about the fundamental aspects of self-assembly of nanocellulose precursors, we review the key strategies needed for material synthesis and to adjust the architecture of the materials (using three-dimensional printing, freeze-casted porous materials, and electrospinning) according to their uses in tissue engineering, artificial organs, controlled drug delivery and wound healing systems, among others. For this purpose, we map the structure-property-function relationships of nanocellulose-based porous materials and examine the course of actions that are required to translate innovation from the laboratory to industry. Such efforts require attention to regulatory aspects and market pull. Finally, the key challenges and opportunities in this nascent field are critically reviewed.

RESUMO

This study reports the fabrication of polymeric matrices through electrospinning using polymethyl methacrylate (PMMA) and poly(lactic-co-glycolic acid) (PLGA), biocompatible polymers commonly used in medical systems. These polymers were combined with an antibacterial drug, sulfadiazine sodium salt (SDS) or its supramolecular system formed with hydroxypropyl-ß-cyclodextrin (HPß/CD) at 1:1 molar ratio, aiming to assemble a transdermal drug delivery system. The formation of fibers was confirmed by scanning electron microscopy (SEM), and the fibers' surface properties were analyzed using contact angle and water vapor permeability techniques. Drug release tests and cell viability assays were performed to evaluate the potential toxicity of the material. SEM images demonstrated that the obtained fibers had nanoscale- and micrometer-scale diameters in PLGA and PMMA systems, respectively. The contact angle analyses indicated that, even in the presence of hydrophilic molecules (SDS and HPßCD), PMMA fibers exhibited hydrophobic characteristics, while PLGA fibers exhibited hydrophilic surface properties. These data were also confirmed by water vapor permeability analysis. The drug release profiles demonstrated a greater release of SDS in the PLGA system. Moreover, the presence of HPßCD improved the drug release in both polymeric systems and the cell viability in the PMMA SDS/HPßCD system. In terms of antibacterial activity, all membranes yielded positive outcomes; nevertheless, the PLGA SDS/HPßCD membrane exhibited the most remarkable results, with the lowest microbial load values. Additionally, the pseudo wound healing analysis demonstrated that the PLGA SDS/HPßCD fiber exhibited results similar to the control group. Consequently, these findings exemplify the substantial potential of the obtained materials for use in wound healing applications.

RESUMO

In the original publication [...].

RESUMO

The bacterial cellulose membrane (CM) is a promising biomaterial due to its easy applicability and moist environment. Moreover, nanoscale silver compounds (AgNO3) are synthesized and incorporated into CMs to provide these biomaterials with antimicrobial activity for wound healing. This study aimed to evaluate the cell viability of CM incorporated with nanoscale silver compounds, determine the minimum inhibitory concentration (MIC) for Escherichia coli and Staphylococcus aureus, and its use on in vivo skin lesions. Wistar rats were divided according to treatment: untreated, CM (cellulose membrane), and AgCM (CM incorporated with silver nanoparticles). The euthanasia was performed on the 2nd, 7th, 14th, and 21st days to assess inflammation (myeloperoxidase-neutrophils, N-acetylglucosaminidase-macrophage, IL-1ß, IL-10), oxidative stress (NO-nitric oxide, DCF-H2O2), oxidative damage (carbonyl: membrane's damage; sulfhydryl: membrane's integrity), antioxidants (superoxide dismutase; glutathione), angiogenesis, tissue formation (collagen, TGF-ß1, smooth muscle α-actin, small decorin, and biglycan proteoglycans). The use of AgCM did not show toxicity, but antibacterial effect in vitro. Moreover, in vivo, AgCM provided balanced oxidative action, modulated the inflammatory profile due to the reduction of IL-1ß level and increase in IL-10 level, in addition to increased angiogenesis and collagen formation. The results suggest the use of silver nanoparticles (AgCM) enhanced the CM properties by providing antibacterial properties, modulation the inflammatory phase, and consequently promotes the healing of skin lesions, which can be used clinically to treat injuries.

Assuntos

RESUMO

In recent years, nanoparticulate materials have aroused interest in the field of organic electronics due to their high versatility which increases the efficiency of devices. In this work, four different stable conformations based on the organic semiconductors P3HT and PC71BM were synthesized using the nanoprecipitation method, including blend and core-shell nanoparticles. All nanoparticles were obtained free of surfactants and in aqueous suspensions following the line of ecologically correct routes. The structural and optoelectronic properties of the nanoparticles were investigated by dynamic light scattering (DLS), transmission electron microscopy (TEM), scanning electron microscopy (SEM), UV-visible absorption spectroscopy and UV-visible photoluminescence (PL). Even in aqueous media, the blend and core-shell nanoparticles exhibited a greater light absorption capacity, and these conformations proved to be effective in the process of dissociation of excitons that occurs at the P3HT donor/PC71BM acceptor interface. With all these characteristics and allied to the fact that the nanoparticles are surfactant-free aqueous suspensions, this work paves the way for the use of these colloids as a photoactive layer of organic photovoltaic devices that interface with biological systems.

RESUMO

Edible films have been studied mainly as primary packaging materials, but they may be used as barrier layers between food components, e.g., by reducing the moisture migration between components with contrasting water activities. Since edible films are part of the food itself, components adding sensory appeal (e.g., fruit purees) are usually desirable. The objective of this study was to develop a film to be applied as a moisture barrier between nachos and guacamole. Ten film formulations were prepared according to a simplex centroid design with three components-a polysaccharide matrix (consisting of a 5:1 mixture of bacterial cellulose-BC-and carboxymethyl cellulose), tomato puree (for sensory appeal), and palm olein (to reduce hydrophilicity)-and produced by bench casting. The film with the highest palm olein content (20%) presented the lowest water vapor permeability, and its formulation was used to produce a film by continuous casting. The film was applied as a layer between nachos and guacamole, and presented to 80 panelists. The film-containing snack was preferred and considered as crispier when compared to the snack without the film, suggesting that the film was effective in reducing the moisture migration from the moist guacamole to the crispy nachos.

RESUMO

Considered a simple and versatile technique, electrospinning has emerged as a technology for developing 3D materials for a wide range of applications [...].