RESUMO

Cellulose cryogels are promising eco-friendly materials that exhibit low density, high porosity, and renewability. However, the applications of these materials are limited by their lower mechanical and water resistance compared to petrochemical-based lightweight materials. In this work, nanocelluloses were functionalized with cationic and anionic groups, and these nanomaterials were combined to obtain strong and water-resilient cryogels. To prepare the cryogels, anionic and cationic micro- and nanofibrils (CNFs) were produced at three different sizes and combined in various weight ratios, forming electrostatic complexes. The complex phase was concentrated by centrifugation and freeze-dried. Porous and open cellular structures were assembled in all compositions tested (porosity >90 %). Compressive testing revealed that the most resistant cryogels (1.7 MPa) were obtained with equivalent amounts of negatively and positively charged CNFs with lengths between 100 and 1200 nm. The strength at this condition was achieved as CNF electrostatic complexes assembled in thick cells, as observed by synchrotron X-ray tomography. In addition to mechanical strength, electrostatic complexation provided remarkable structural stability in water for the CNF cryogels, without compromising their biodegradability. This route by electrostatic complexation is a practical strategy to combine and concentrate nanocelluloses to tailor biodegradable lightweight materials with high strength and wet stability.

RESUMO

Nanocellulose is a well-known stabilizer for several colloidal dispersions, including emulsions and solid nanoparticles, replacing surfactants, polymers, and other additives, and therefore providing more minimalistic and eco-friendly formulations. However, could this ability be extended to stabilize oil droplets and inorganic nanoparticles simultaneously in the same colloidal system? This work aimed to answer this question. We evaluated both cationic and anionic nanofibrillated celluloses to stabilize both titanium dioxide nanoparticles and oil droplets. The resulting suspensions held their macroscopic stability for up to 2 months, regardless of pH or surface charge. Cryo-TEM images revealed a complex network formation involving nanofibers and TiO2 nanoparticles, which agrees with the high viscosity values and gel-like behavior found in rheology measurements. We propose that the formation of this network is responsible for the simultaneous stabilization of oil droplets and TiO2 nanoparticles, and that this may be used as a formulation tool for other complex systems.

Assuntos

RESUMO

Elucidating cellulose-lignin interactions at the molecular and nanometric scales is an important research topic with impacts on several pathways of biomass valorization. Here, the interaction forces between a cellulosic substrate and lignin are investigated. Atomic force microscopy with lignin-coated tips is employed to probe the site-specific adhesion to a cellulose film in liquid water. Over seven thousand force-curves are analyzed by a machine-learning approach to cluster the experimental data into types of cellulose-tip interactions. The molecular mechanisms for distinct types of cellulose-lignin interactions are revealed by molecular dynamics simulations of lignin globules interacting with different cellulose Iß crystal facets. This unique combination of experimental force-curves, data-driven analysis, and molecular simulations opens a new approach of investigation and updates the understanding of cellulose-lignin interactions at the nanoscale.

Assuntos

RESUMO

Cellulose disassembly is an important issue in designing nanostructures using cellulose-based materials. In this work, we present a combination of experimental and theoretical study addressing the disassembly of cellulose nanofibrils. Through 2,2,6,6-tetramethylpiperidine-1-oxyl-mediated oxidation processes, combined with atomic force microscopy results, we show the formation of nanofibers with diameters corresponding to that of a single-cellulose polymer chain. The formation of these polymer chains is controlled by repulsive electrostatic interactions between the oxidized chains. Further, first-principles calculations have been performed in order to provide an atomistic understanding of the cellulose disassembling processes, focusing on the balance between the interchain (IC) and intersheet (IS) interactions upon oxidation. First, we analyze these interactions in pristine systems, where we found the IS interaction to be stronger than the IC interaction. In the oxidized systems, we have considered the formation of (charged) carboxylate groups along the inner sites of elementary fibrils. We show a net charge concentration on the carboxylate groups, supporting the emergence of repulsive electrostatic interactions between the cellulose nanofibers. Indeed, our total energy results show that the weakening of the binding strength between the fibrils is proportional to the concentration and net charge density of the carboxylate group. Moreover, by comparing the IC and IS binding energies, we found that most of the disassembly processes should take place by breaking the IC O-H···O hydrogen bond interactions and thus supporting the experimental observation of single- and double-cellulose polymer chains.

RESUMO

Supramolecular assembly of biobased components in water is a promising strategy to construct advanced materials. Herein, electrostatic complexation was used to prepare wet-resilient foams with improved mechanical property. Small-angle X-ray scattering and cryo-transmission electron microscopy experiments showed that suspensions with oppositely charged cellulose nanofibers are a mixture of clusters and networks of entangled fibers. The balance between these structures governs the colloidal stability and the rheological behavior of CNFs in water. Foams prepared from suspensions exhibited maximum compressive modulus at the mass composition of 1:1 (ca 0.12 MPa), suggesting that meaningful attractive interactions happen at this point and act as stiffening structure in the material. Besides the electrostatic attraction, hydrogen bonds and hydrophobic contacts may also occur within the clustering, improving the water stability of cationic foams. These results may provide a basis for the development of robust all- cellulose materials prepared in water, with nontoxic chemicals.

Assuntos

RESUMO

Nanocellulose is a promising material for fabricating green, biocompatible, flexible, and foldable devices. One of the main issues of using nanocellulose as a fundamental component for wearable electronics is the influence of environmental conditions on it. The water adsorption promotes the swelling of nanopaper substrates, which directly affects the devices' electrical properties prepared on/with it. Here, plant-based nanocellulose substrates, and ink composites deposited on them, are chemically modified using hexamethyldisilazane to enhance the system's hydrophobicity. After the treatment, the electrical properties of the devices exhibit stable operation under humidity levels around 95%. Such stability demonstrates that the hexamethyldisilazane modification substantially suppresses the water adsorption on fundamental device structures, namely, substrate plus conducting ink. These results attest to the robustness necessary to use nanocellulose as a key material in wearable devices such as electronic skins and tattoos and contribute to the worldwide efforts to create biodegradable devices engineered in a more deterministic fashion.

Assuntos

RESUMO

HYPOTHESIS: Hydrophobic oleic acid/water interfaces are negatively charged. Hence, the use of cationic nanocelluloses as stabilizers of Pickering emulsions could improve the colloidal stability due to the electrostatic complexation at the oil-water interface. EXPERIMENTS: Two cationic nanofibrillated cellulose (cNFCs) with two degrees of substitution were prepared and used as stabilizers of Pickering emulsions. The adsorption of cNFCs at the oil: water interface was evaluated by interfacial tension, atomic force microscopy, and centrifugation measurements. LUMiSizer and optical microscopy techniques were used to analyze the colloidal stability and oil droplets morphology, respectively. Besides, the rheological behavior of the continuous aqueous phase was determined through flow and stress sweep curves. Finally, the dispersion of cNFCs in a diluted emulsion was visualized by cryogenic transmission electron microscopy (cryo-TEM). FINDINGS: Cationic NFCs were more efficient in partitioning to the oil:water interface compared to their anionic analogous, oCNF. The electrostatic attraction between the positively charged trimethylammonium groups and the negatively charged deprotonated oleic acid reduced the interfacial tension and improved the colloidal stability of O/W Pickering emulsions. cNFCs dispersed in the aqueous phase were found to increase the viscosity, decelerating the oil drops coalescence. Therefore, the stabilization of cNFCs Pickering emulsions had a synergistic effect from the electrostatic complexation at the liquid-liquid interface and network formation in the aqueous phase, as visualized by cryo-TEM.

RESUMO

Protozoa parasites are responsible for several diseases in tropical countries, such as malaria, sleeping sickness, Chagas disease, leishmaniasis, amebiasis, and giardiasis, which together threaten millions of people around the world. In addition, most of the classic parasitic diseases due to protozoa are zoonotic. Understanding the biology of these organisms plays a relevant role in combating these diseases. Using homology inference and comparative genomics, this study targeted 3 protozoan species from different Phyla: Cryptosporidium muris (Apicomplexa), Entamoeba invadens (Amoebozoa), and Trypanosoma grayi (Euglenozoa). In this study, we propose a new approach for the identification of homologs, based on the reconciliation of the results of 2 different homology inference software programs. Our results showed that 46.1% (59/128) of the groups inferred by our reconciliation approach could be validated using this methodology. These validated groups are here called homologous Supergroups and were compared with SUPERFAMILY and Pfam Clans.

RESUMO

This study reports the preparation and characterization of nickel/lead hydroxide nanoparticles used to construct electrochemical sensors, which were investigated for amperometric quantification of N-acetylcysteine (NAC). The newly synthesised material presents good uniformity, with the lead (II) ions homogenously incorporated into the alpha nickel hydroxide crystal structure, confirmed by X-ray diffraction, transmission electron microscopy and X-ray photoelectron spectroscopy analyses. Films of nanoparticles (3 nm in size) were prepared on conductive fluorine-doped tin oxide-coated glass slides and used connected to a specially built batch injection analysis (BIA) cell with a capacity of only 4 mL and the electrode positioned in the bottom. To attain optimal analytical performance, the main parameters for BIA measurements (volume injected, different velocities of injection and best distance of the pipette from the electrode) were evaluated, as was the working potential, to determine the optimal conditions. Linear responses were obtained for the concentration range from 20 to 220 µmol L-1, and the limits of detection (3σ/slope) and quantification (10σ/slope) were calculated as 0.23 µmol L-1 and 0.70 µmol L-1, respectively. The new NAC sensor does not exhibit a memory effect and has enormous potential utility in the quantitative determination of N-acetylcysteine in drugs. The results of the analysis of NAC obtained using BIA presented good concordance with those obtained by chromatography. The analytical frequency attained using BIA (120 analysis h-1) compares very favourably with the one obtained using chromatography (6 analysis h-1).

Assuntos

RESUMO

Phase behavior of surfactants in water may be affected by the addition of a third component, and the present study discusses how long-chain n-alcohols affect phase transitions of systems formed by the surfactant hexadecyltrimethylammonium bromide, C16TAB, or its complex salts formed with polyacrylate, C16TAPA30, as well as other previously reported complex salts/water/alcohol systems. Structural characterization by X-ray diffraction patterns at small and wide angles and different temperatures was performed for samples containing n-decanol, n-dodecanol, or n-tetradecanol. Differential scanning calorimetry (DSC) was also used to study the phase transition. The results allowed us to observe and understand the coexistence of lamellar gel (Lß) and lamellar liquid-crystal (Lα) phases, elucidating the structure of a previously reported mesophase, proposing an alternative assignment. Whereas the chain-melting transition is well-known to be sharp for lipids, we have found that it is broader for C16TAB and C16TAPA in the presence of these n-alcohols. We have investigated the effects of their composition and chain length on the temperature and enthalpy of transition. This elucidates why the addition of n-alcohols with chains slightly shorter than that of the surfactants leads to the formation of an ordered gel-like lamellar phase (Lß). n-Alcohols act as neutral cosurfactants, leading to more packing, and all of the factors converge to a limit situation, associated with a common critical area occupied by each alkyl chain. We compared our results with other mesophase systems from the literature, demonstrating that the same trends of phase behavior occur for complex salts of other polyelectrolytes with alkyltrimethylammonium surfactants.