RESUMO

OBJECTIVE: The aim of this study was to compare the Morse taper (MT) + titanium base (Ti-Base) abutment with the external hexagon (EH) + Ti-Base abutment by using the strain gauge method in the mesial, distal, and apical-buccal areas around these types of implants. MATERIALS AND METHODS: This study investigated two groups, MT and EH, each comprising five polyurethane samples with a dental implant in the area of artificial tooth 15 (3.75 × 11.5 mm) of a dental manikin. The strain gauges were glued to the mesial, distal, and apical-buccal polyurethane areas of all samples in relation to the implant. Ti-Base nonangled abutments measuring 5.0 × 4.7 × 1.0 mm (DSP, Brazil) were installed on the implants in each group. Ten identical zirconia crowns were constructed by scanning and milling and were subsequently cemented onto the Ti-base abutments with calcium hydroxide cement. Then, an axial load of 100 N was applied to the occlusal region of the zirconia crowns, and strain gauge measurements were taken. STATISTICAL ANALYSIS: Strain gauge data were assessed by a two-way analysis of variance (ANOVA) with "implant connection" and "strain gauge position" factors, followed by the Bonferroni test (p < 0.05). RESULTS: The MT group exhibited a statistically significant reduction in microstrain in the mesial and apical strain gauge measurements compared to the EH group. CONCLUSION: The MT group exhibited less microstrain in the mesial and apical areas of the polyurethane samples near the implant. Consequently, the MT connection was considered more biomechanically advantageous.

RESUMO

This study aimed to compare the mechanical properties of various occlusal plate materials by analyzing surface roughness, Knoop microhardness, flexural strength, and modulus of elasticity. Fifty samples were prepared and classified as SC (self-curing acrylic resin), WB (heat-cured acrylic resin), ME (acrylic resin polymerized by microwave energy), P (resin print), and M (polymethylmethacrylate polymer block for computer-aided design/computer-aided manufacturing). The data were analyzed using a one-way analysis of variance and Tukey's honestly significant difference test. Surface roughness was the same in all groups. The surface hardness of group M was statistically superior. The samples from groups P and M had higher flexural strength than other samples. The modulus of elasticity of group SC was statistically lower than that of other groups. The mechanical properties of the materials used to make the occlusal plates differed, and group M achieved the best results in all analyses. Therefore, clinicians must consider the material used to manufacture long-lasting and efficient occlusal splints.

Assuntos

RESUMO

Abstract This study aimed to compare the mechanical properties of various occlusal plate materials by analyzing surface roughness, Knoop microhardness, flexural strength, and modulus of elasticity. Fifty samples were prepared and classified as SC (self-curing acrylic resin), WB (heat-cured acrylic resin), ME (acrylic resin polymerized by microwave energy), P (resin print), and M (polymethylmethacrylate polymer block for computer-aided design/computer-aided manufacturing). The data were analyzed using a one-way analysis of variance and Tukey's honestly significant difference test. Surface roughness was the same in all groups. The surface hardness of group M was statistically superior. The samples from groups P and M had higher flexural strength than other samples. The modulus of elasticity of group SC was statistically lower than that of other groups. The mechanical properties of the materials used to make the occlusal plates differed, and group M achieved the best results in all analyses. Therefore, clinicians must consider the material used to manufacture long-lasting and efficient occlusal splints.

RESUMO

Background: To evaluate the stress distribution of three-element prostheses on two different implant systems (External Hexagon (EH) or Morse Taper (MT)) and with two different retention mechanisms (screw-retained or cemented), by photoelastic analysis and strain gauge analyses. Material and Methods: Four photoelastic and 24 strain gauge models of a partially edentulous maxilla were made and were divided in four groups according to connection and retention system: Group I (EH-C) - external hexagon+cement-retained prosthesis; Group II (EH-S) external hexagon+screw-retained prosthesis; Group III (MT-C) - morse taper+cement-retained prosthesis; Group IV (MT-S) - morse taper+screw-retained prosthesis. The implants were installed in the axial position, the first in the region of element 15 and the distal implant in the region of element 17. Loads of 100 N were applied on the occlusal surface of the prosthesis for 10 seconds. For the photoelasticity analysis, photographic images were taken and were evaluated according to the number of high-intensity fringes. For the strain gauge analysis, the strain gauges were positioned on the marginal crest of the implants and on the apical region, being numbered for analysis of the stress distribution in each region. The electrical signals were captured and processed by specific software. Results: Higher concentration of tension was observed in the apical region of the implants and mainly in the distal implant, where the formation of fringes was higher. The microstrain values obtained for each group were similar: EH-C (454±18,3 µÉ›); EH-S (469±94 µÉ›); MT-C (466±49,8 µÉ›); MT-S (460±36,6 µÉ›). It was observed that apical position had higher stress concentrations for all analyzed groups. Conclusions: The different connections and fixation mode did not interfere in the amount of tension generated in the tissue adjacent to the implant, also the region that generated the greatest amount of tension was in the apical region of the anterior implant. Key words:Dental implants, biomechanics, fixed prosthodontics.

RESUMO

A Odontologia atual apresenta relevantes mudanças no processo de reabilitação oral. Com isso, a instalação de implantes osseointegrados, constituem uma importante ferramenta neste âmbito, pois permitem a devolução da função mastigatória, permitindo também que os pacientes tenham a estética recuperada. O presente trabalho tem como objetivo realizar uma revisão de literatura, sobre a importância de um planejamento prévio, chamado também de planejamento reverso, o mesmo aponta um maior sucesso no processo reabilitador, apresentando-se como uma técnica que busca facilitar e estudar a correta reabilitação do paciente, proporcionando uma melhor previsibilidade para o tratamento, a partir do momento em que se planeja a reabilitação oral protética antes mesmo de se pensar no processo cirúrgico de implantes osseointegrados. Conclui-se com esse trabalho que o sucesso do tratamento com implantes depende diretamente de um prévio plano de tratamento, independentemente da extensão da área edêntula, quando é realizado um planejamento reverso diminuiu-se a taxa de intercorrências, além de aumentar a taxa de sucesso no processo de reabilitação(AU)

Current Dentistry presents relevant changes in the oral rehabilitation process. As a result, the installation of osseointegrated implants is na important tool in this context, as it allows the return of lost teeth, also allowing patients to have their function and aesthetics recovered. For greater success of the rehabilitation process, reverse planning presents itself as a technique that seeks to facilitate the correct rehabilitation of the patient, allowing better predictability for the treatment from the moment that the prosthetic oral rehabilitation is planned before even thinking about the surgical process of osseointegrated implants. The success of treatment with implants depends directly on a properly planned treatment plan, regardless of the extent of the edentulous area. This paper aims to conduct a literature review on the importance of reverse planning in implantology(AU)

Assuntos

RESUMO

O objetivo deste estudo é realizar uma revisão da literatura para identificar os principais fatores que levam às complicações em implantodontia. Os implantes osseointegráveis e sua aplicação na odontologia revolucionaram a reabilitação oral de pacientes sejam eles edêntulos totais ou parciais em busca de recuperação funcional e satisfação estética. A pesquisa científica em uma busca constante pela magnificação deste tratamento, possibilitaram o uso de reabilitações implantossuportadas como um método de tratamento previsível com um índice elevado de sucesso. No entanto, como qualquer modo de tratamento, complicações e falhas também podem ocorrer na implantodontia. Após a revisão de literatura pode-se concluir que as condições médicas do paciente, hábitos sociais e parafuncionais, inexatidão do planejamento cirúrgico e protético, conhecimento técnico e científico do cirurgião-dentista, a falta de relacionamento interdisciplinar e deficiente cooperação do paciente no pós-operatório, podem estar relacionadas às complicações no tratamento reabilitador com implantes dentários(AU)

The objective of this study is to carry out a complete literature review to elucidate and evaluate the factors that lead to complications in implantology. The osseointegrated implantsimplants and their application in dentistry have revolutionized the oral rehabilitation of patients who need this treatment, be they total or partial edentulous in search of functional recovery and aesthetic satisfaction. Scientific research and a constant search for the magnification of this treatment, allowed the use of implant-enhanced rehabilitation as a predictable treatment method with a high success rate. However, like any treatment mode, complications and failures can also occur in implantology. the patient's medical conditions, social and parafunctional habits, inaccuracy of surgical and prosthetic planning, technical and scientific knowledge of the dental surgeon, lack of interdisciplinary relationship and poor patient cooperation in the postoperative, may be related to complications in rehabilitating treatment with dental implants(AU)

Assuntos

RESUMO

AIM: To evaluate the cytotoxicity and inflammatory response of different types of provisional restorative materials to mice gingival fibroblasts. METHODS: Cytotoxicity of provisional material discs (thermal-polymerized acrylic resin; auto-polymerized acrylic resin; bisacrylic resin; nano-ceramic resin for CAD/CAM and prefabricated polymer block for CAD/CAM) to Mice (Balb/c) gingival cell were investigated under direct and indirect contact (extracts) at 24, 48 and 72 h, using the MTT and Alamar blue assays. Materials extracts (24 h) were applied to the cell culture (indirect contact) or cells were seeded on discs of provisional materials, and the cytotoxicity and production of IL-6, IL-1ß and TNF-α after 24, 48 and 72 h were analyzed through MTT, Alamar Blue® and ELISA. Culture medium was used as control for indirect contact assay (extract) and the surfaces of the wells without discs of provisional materials were used as control for direct contact assay. Results were analysed statistically by ANOVA followed by the Bonferroni-Test correction. Statistically significant differences were considered if P was < .05. RESULTS: Auto-polymerized and bisacrylic resins (direct contact) reduced cell viability after 24, 48 and 72 h compared to control (P < .05). Indirect contact (extract) was not cytotoxic to cells at all periods compared to control (P > .05). Auto-polymerized and bisacrylic resins increased IL-6, IL-1ß and TNF-α levels mainly at 24 h when compared to the other materials (P < .001). CONCLUSION: Auto-polymerized and bisacrylic were more cytotoxic to mice gingival fibroblasts. CAD/CAM nano ceramic resin and prefabricated polymer blocks are more predictable materials to preserve the periodontal soft tissues.

Assuntos

RESUMO

BACKGROUND: The aim of this study was to evaluate the distribution of stress in complete fixed mandibular prostheses with infrastructures (IE) fabricated with different materials and techniques, under compressive force. MATERIAL AND METHODS: A model of an edentulous mandible, which received five 4x11 mm external hexagon implants between the mental foramens, was fabricated. The groups were divided into: Group I - IE in nickel-chromium with an acrylic resin occlusal coating; Group II - IE in nickel-chromium with a ceramic occlusal coating; Group III - IE milled in zirconia with a ceramic coating. For the photoelastic methodology, 70 N axial loads were applied in three regions. Photographic images were taken and analyzed according to the number of high-intensity fringes. For the strain gauge methodology, the measurement of stresses was performed in two distinct regions. The same compression tests described earlier were then performed. The registered stress values were grouped in tables and submitted to two-factor variance analysis (ANOVA) and the Tukey test with 5% significance. RESULTS: The results of the two methodologies demonstrated smaller stress values for Group I, when compared to the other groups. CONCLUSIONS: It was possible to conclude that the complete fixed prostheses, with infrastructures cast in metal and acrylic occlusal coating, demonstrated better biomechanical results. Key words:Dental implants, mandibular prosthesis implantation, biomechanics.

RESUMO

Para alcançar a estética em dentes anteriores deve-se ter conhecimento de diversas técnicas e principalmente fazer a escolha correta dos materiais. As cerâmicas odontológicas estão cada vez mais presentes nas restaurações, visto que possuem ótimas propriedades ópticas e mecânicas. Assim, o objetivo deste estudo foi proporcionar a estética em dentes anteriores com diferentes subtratos através de uma prótese fixa metal-free. Paciente do gênero masculino, 38 anos, procurou atendimento queixando-se da estética do seu sorriso. No exame clínico foi observada uma coroa total metalocerâmica no elemento 21 e facetas de resina composta nos elementos 11,12 e 22, todas com estética insatisfatória. O dente 21 apresentava um núcleo metálico fundido adequado e os dentes 12 e 22 com tratamentos endodônticos. Foi proposta a instalação de pinos de fibra de vidro nos dentes 12 e 22. Além, da confecção de coroas totais metais-free em dissilicato de lítio nos quatro incisivos superiores com o sistema e-max ceram. O resultado final estético e funcional foi aprovado pelo paciente e pelos profissionais envolvidos(AU)

To achieve aesthetics in anterior teeth one must be aware of several techniques and especially make the correct choice of materials. Dental ceramics are increasingly present in restorations, since they have excellent optical and mechanical properties. Thus, the objective of this study was to achieve esthetics in anterior teeth with different substrate through a fixed prosthesis metal-free. A male patient, 38 years old, sought care complaining about the aesthetics of his smile. In the clinical examination a total metaloceramic crown was observed in element 21 and composite resin facets in elements 11,12 and 22, all with unsatisfactory aesthetics. Tooth 21 had a suitable molten metal core and teeth 12 and 22 with endodontic treatments. It was proposed to install fiberglass pins on the teeth 12 and 22. In addition, from the manufacture of total metal-free crowns in lithium disilicate in the four upper incisors with the e-max system ceram. The final aesthetic and functional result was approved by the patient and the professionals involved(AU)

Para alcanzar la estética en dientes anteriores se debe tener conocimiento de diversas técnicas y principalmente hacer la elección correcta de los materiales. Las cerámicas dentales están cada vez más presentes en las restauraciones, ya que poseen óptimas propiedades ópticas y mecánicas. Así, el objetivo de este estudio fue proporcionar la estética en dientes anteriores con diferentes sustratos a través de una prótesis fija metal-free. Paciente del género masculino, 38 años, buscó atención quejándose de la estética de su sonrisa. En el examen clínico se observó una corona total metalocerámica en el elemento 21 y facetas de resina compuesta en los elementos 11,12 y 22, todas con estética insatisfactoria. El diente 21 presentaba un núcleo metálico fundido adecuado y los dientes 12 y 22 con tratamientos endodónticos. Se propuso la instalación de pines de fibra de vidrio en los dientes 12 y 22. Además, de la confección de coronas totales metales libres en disilicato de litio en los cuatro incisivos superiores con el sistema e-max ceram. El resultado final estético y funcional fue aprobado por el paciente y los profesionales involucrados(AU)

Assuntos

RESUMO

Devido a evolução dos sistemas cerâmicos, atualmente, são permitidas inúmeras associações de materiais restauradores. Entretanto, mimetizar as características visuais das próteses livres de metal com próteses metalocerâmica permanece um desafio. Assim, o objetivo deste trabalho foi relatar o caso clínico de substituição de próteses desadaptadas, homogeneizando próteses parciais fixas livres de metal e metalocerâmicas dento e implantossuportadas, após cirurgia periodontal. O paciente de 55 anos, gênero masculino, compareceu à Clínica de Prótese Parcial Fixa, da Faculdade de Odontologia de Araçatuba ­ FOA/UNESP em 2017 queixando-se dos seus dentes anteriores estarem "feios" e com a "raiz aparecendo". No exame clínico foi constatada recessão gengival nos elementos 11 e 13, os quais continham uma prótese parcial fixa de três elementos metalocerâmicas desadaptada, prótese sobre implante nos elementos 21 e 22, que apresentavam-se desadaptadas e com estética desfavorável. No exame radiográfico pôde-se observar a presença de um núcleo metálico fundido nos elementos 11 e 13. Foi proposto, então, a confecção de coroas totais livres de metal nos elementos anteriores superiores (13, 12, 11, 21 e 23) e coroa metalocerâmica para o elemento 22. Para isso, foi realizado enceramento diagnóstico inicial e, após o consentimento do paciente, foi efetuada a remoção das próteses antigas. Com a remoção, visualizamos uma . depressão na vestibular do rebordo na área do 12 (ausente), solucionado com um enxerto gengival subepitelialApós a realização dos preparos dentários e moldagem com silicone de adição as peças foram confeccionadas com sistema e.max Ceram (Ivoclar Vivadent). Após a prova estética e ajustes oclusais iniciais, as peças foram preparadas para cimentação resinosa com o sistema Variolink® N (Ivoclar Vivadent). O cimento transparente Conclui-se que, apesar da disparidade dos materiais, é possível mimetizá-los e foi selecionado previamente por meio de provas com o kit Try-In.oferecer resultados reabilitadores suficientemente estéticos e satisfatórios(AU)

Due to the evolution of ceramic systems, numerous associations of restorative materials are now permitted. However, mimicking the visual characteristics of metal-free prostheses with metal-ceramic dentures remains a challenge. Thus, the objective of this study was to report the clinical case of replacement of maladaptive dentures, homogenizing denture free and fixed metal partial dentures and implants supported after periodontal surgery. The patient, 55 years old, male, attended the Fixed Partial Prosthesis Clinic of the Faculty of Dentistry of Araçatuba - FOA / UNESP in 2017 complaining that his anterior teeth were "ugly" and with the "root appearing". In the clinical examination, gingival recession was observed in elements 11 and 13, which contained a fixed partial prosthesis of three maladaptive metal-ceramic elements, a prosthesis on implants in elements 21 and 22, the prostheses were maladapted and unfavorable esthetics. In the radiographic examination it is possible to observe the presence of a molten metal nucleus in elements 11 and 13. It was proposed, then, the manufacture of free metal crowns in the upper anterior elements (13, 12, 11, 21 and 23) and crown PFM for the element 22. For this, it performed waxing initial diagnosis and after the patient's consent, the removal of the old prosthesis were performed. Upon removal, a depression visualize the buccal flange in the area 12 (absent), solved with a subepithelial gum graft. After the dental preparations and molding with silicone of addition the pieces were made with e.max Ceram system (Ivoclar Vivadent). After the initial test and aesthetic occlusal adjustments, the pieces were prepared for cementing with resin Variolink® N system (Ivoclar Vivadent). The clear cement was previously selected by the test realized with Try-In kit. We conclude that, despite the disparity of materials, it is possible to mimic them and offer rehabilitative results sufficiently aesthetic and satisfactory(AU)

Debido a la evolución de los sistemas cerámicos, actualmente, se permiten numerosas asociaciones de materiales restauradores. Sin embargo, mimetizar las características visuales de las prótesis libres de metal con prótesis metalocerámicas sigue siendo un desafío. Así, el objetivo de este trabajo fue relatar el caso clínico de sustitución de prótesis desadaptadas, homogeneizando prótesis parciales fijas libres de metal y metalocerámicas dento e implantosuportadas, después de cirugía periodontal. El paciente de 55 años, género masculino, asistió a la Clínica de Prótesis Parcial Fija, de la Facultad de Odontología de Araçatuba - FOA / UNESP en 2017 quejándose de sus dientes anteriores estar "feos" y con la "raíz apareciendo". En el examen clínico se constató recesión gingival en los elementos 11 y 13, los cuales contenían una prótesis parcial fija de tres elementos metalocerámicos desadaptados, prótesis sobre implante en los elementos 21 y 22, las prótesis se presentaban desadaptadas y con estética desfavorable. En el examen radiográfico se puede observar la presencia de un núcleo metálico fundido en los elementos 11 y 13. Se propuso entonces la confección de coronas totales de metal en los elementos anteriores superiores (13, 12, 11, 21 y 23) y corona metalocerámica para el elemento 22. Para ello, se realizó el encerado diagnóstico inicial y, tras el consentimiento del paciente, se efectuó la remoción de las prótesis antiguas. Con la remoción, visualizamos una depresión en la vestibular del borde en el área del 12 (ausente), solucionado con un injerto gingival subepitelial. Después de la realización de los preparados dentales y moldeo con silicona de adición las piezas fueron confeccionadas con sistema e.max Ceram (Ivoclar Vivadent). Después de la prueba estética y ajustes oclusales iniciales, las piezas fueron preparadas para cementación resinosa con el sistema Variolink® N (Ivoclar Vivadent). El cemento transparente fue seleccionado previamente por medio de pruebas con el kit Try-In. Se concluye que, a pesar de la disparidad de los materiales, es posible mimetizarlos y ofrecer resultados rehabilitadores suficientemente estéticos y satisfactorios(AU)

Assuntos