RESUMO
The upflow anaerobic hybrid (UAHB) reactor combines the advantages of a upflow anaerobic sludge blanket (UASB-type) reactor and an anaerobic filter in a single compartment. A novel configuration of the UAHB reactor, composed of two three-phase separators (3PHS), was proposed to evaluate the biogas production in the moving and fixed bed in the treatment of synthetic sewage at a temperature range of 14-21â °C and hydraulic retention time (HRT) of 12, 10 and 8â h. The bench-scale reactor was operated in three different phases with organic loading rate (VOLR) of 0.6 (0.3-0.7), 0.7 ± 0.2, and 1.1 ± 0.1â kg COD m-3 d-1, respectively, for 225 days. The average removal efficiency of chemical oxygen demand (CODt) was 78 (42-89)%, and the total biogas yield was 3090 (1704-4782) mL d-1, with 66% of the lower 3PHS (moving bed) and 34% of the upper 3PHS (fixed bed). However, no significant difference was observed between the biogas yield on the 3PHS (p-value = 0.5048), thus confirming the influence of temperature in the biogas production. The average percentage of methane was 76 (60-82)% for both beds, and the filter media increased the production by 21%. Thus, it can be concluded that the fixed bed suppressed the instability of the moving bed regarding the biogas production and contributed to the final quality of the effluent.
Assuntos
Biocombustíveis , Eliminação de Resíduos Líquidos , Anaerobiose , Temperatura , Reatores Biológicos , Esgotos , MetanoRESUMO
Recent studies point out losses of 30-40% of the produced methane in the effluent of anaerobic reactors treating sewage, reducing the renewable energy potential and the environmental footprint. A novel bench-scale upflow anaerobic hybrid (UAHB) reactor combining a sludge blanket at the bottom and a filter media at the top, both with three-phase separators, was proposed to evaluate the recovery of dissolved methane. UAHB was operated with volumetric organic loading rate of 1.24â kg CODâ m-3â d-1 and hydraulic retention time of 8â h for 218 days to evaluate the influence of temperature (18°C, 23°C, and 28°C) in the methane dissolved in the effluent and collected from three-phase separators. Chemical oxygen demand (COD) and total suspended solids (TSS) removals efficiencies remained constant during the operation and equal to 90 and 95%, respectively, related to the activity of biomass retained in the filter media. Temperature increase influenced more the methane production in the sludge blanket rather than in the upper bed. The volume of recovered methane increased about 20% with the installation of the support media and the upper three-phase separator (3PHS). The loss of methane dissolved in the effluent was strongly influenced by the temperature, and higher with the decrease of this parameter. Non-statistically significant correlations were observed between the temperature and the methane production in the upper bed (p-value = 0.0943) and total (p-value = 0.0930). Thus, it can be concluded that the evaluated temperatures did not influence the global efficiency and the total methane yield of the UAHB reactor.
Assuntos
Reatores Biológicos , Esgotos , Eliminação de Resíduos Líquidos , Anaerobiose , Temperatura , MetanoRESUMO
The constant presence of triclosan (TCS) in surface water and wastewater has been verified due to its application in several pharmaceutical and personal care products. Thus, removing this emerging contaminant is essential to minimize the contamination of water bodies. The anaerobic-aerobic-anoxic (AOA) system is an innovative alternative that combines the removal of nutrients and triclosan. This study focuses on the simultaneous removal of carbonaceous matter, nitrogen, phosphorus, and triclosan in a continuous pilot-scale AOA system from synthetic wastewater. The upflow system, in series, was operated at hydraulic retention time (HRT) of 8â h and a flowrate of 2.40 L h-1. Glucose (190â mg L-1) was added to the anoxic reactor as the external carbon source. Besides that, bacterial community structure was investigated using 16S rRNA sequencing in each reactor. The system achieved average removal efficiencies of 96% (14.03â g d-1) for Chemical Oxygen Demand (COD), 85% (2.64â g d-1) for Total Kjeldahl Nitrogen (TKN), 88% (1.40â g d-1) for Total Ammonia Nitrogen (TAN), 20% (0.12â g d-1) for Total Phosphorus (TP), and 93% (1.87 µg d-1) for Triclosan (TCS). The phyla Proteobacteria, Firmicutes, Bacteroidetes, and Chloroflexi were found in greater abundance. The main genera identified were Anaeromusa, Aeromonas, Azospira, Clostridium, and Lactococcus. The organisms related to phylum and genus corroborate the involved processes and the removal performance achieved. In addition, Lactococcus, Thermomonas, Ferruginibacter, and Dechloromonas were involved in triclosan biodegradation. The anaerobic-oxic-anoxic system successfully removed carbonaceous, nitrogenous matter, and triclosan, with glucose increasing the denitrifying activity.
RESUMO
RESUMO Sistemas alagados construídos (SACs) são alternativas de engenharia para tratamento de águas residuárias. Entretanto, ainda são limitadas as pesquisas relacionadas à hidrodinâmica desses sistemas, quando comparados a outras unidades de tratamento, como filtros biológicos, reatores anaeróbios, lagoas de estabilização, dentre outros. Dessa forma, neste estudo teve-se como objetivo avaliar o comportamento hidrodinâmico de três SACs de escoamento horizontal subsuperficial (plantados e não plantados) em escala piloto, por meio da injeção dos traçadores cloreto de lítio, dextrana azul e rodamina WT. Utilizaram-se diferentes metodologias de normalização, para vazão constante e para vazão variável, para avaliar o efeito da variação da taxa de escoamento no sistema. Além disso, determinaram-se os índices hidrodinâmicos e o grau de dispersão dos sistemas por meio dos modelos de escoamento tanques em série e escoamento disperso. Os valores recuperados de rodamina WT e de lítio foram satisfatórios, maiores do que 80% da massa injetada nos três SACs. Para a dextrana azul, a taxa recuperação não foi validada. Não foram verificadas diferenças nas curvas de distribuição de tempo de retenção submetidas às duas metodologias de normalização. Os índices hidrodinâmicos determinados revelaram baixo grau de curtos-circuitos, boa eficiência hidráulica e mistura nos sistemas. Os sistemas apresentaram grau de dispersão moderada, o que está de acordo com os resultados obtidos pelos índices hidrodinâmicos.
ABSTRACT Constructed wetlands (CWs) are engineering alternatives for wastewater treatment. However, the scientific literature related to the hydrodynamics of these systems is still scarce when compared to other treatments, such as trickling filters, anaerobic reactors, stabilizations ponds, among others. Thus, this study aimed to evaluate the hydrodynamic behavior of three subsurface horizontal flow CWs (vegetated and unvegetated) on a pilot scale by injecting the tracers lithium chloride, blue dextran, and rhodamine WT. Different normalization methodologies for constant and variable flows were used to evaluate the effect of flow rate variation on the system. In addition, hydrodynamic indices and the system dispersion degree were determined by tank-in-series and dispersion models. The recovered mass of rhodamine WT and lithium was greater than 80% in the three systems, considered satisfactory. For the blue dextran, the recovery rate was not validated. Residence time distribution curves were submitted to two normalization methodologies. No difference was detected. The hydrodynamic indices found revealed low short circuit level, good hydraulic efficiency and mixing in the systems. The systems presented a moderate degree of dispersion, agreeing with the results obtained by the hydrodynamic indices.
RESUMO
RESUMO O tipo de material utilizado como recheio em filtros anaeróbios pode ser determinante na eficiência do tratamento, então a avaliação de novos materiais se torna importante. Assim, o objetivo deste trabalho foi estudar o comportamento de três filtros anaeróbios de fluxo ascendente, operados de modo contínuo, preenchidos com carvão ativado, cerâmica de argila e borracha de pneu, no tratamento de água residuária sintética com glicose como substrato. Os filtros, em escala de bancada (1,3 L), foram operados com tempo de detenção hidráulica (TDH) de oito e quatro horas, em duas etapas. Seu desempenho, avaliado com o emprego dos parâmetros pH, alcalinidade total e bicarbonato e ácidos voláteis, foi estável nas duas etapas de operação. O filtro que obteve maior eficiência em termos de remoção de demanda química de oxigênio (DQO) foi o com carvão ativado, 94 e 81% nas etapas I e II, respectivamente, seguido do com borracha de pneu, 88 e 63%, e do com cerâmica de argila, 81 e 61%, ambos nas etapas I e II, respectivamente. As principais morfologias encontradas nos meios suportes foram bacilos, cocos, filamentos, Methanosaeta sp. e Methanosarcina sp. As diferenças obtidas entre os filtros podem ser relacionadas com as características distintas de cada material utilizado como meio suporte, e as diferenças entre as etapas ocorrem pelo aumento da carga hidráulica, que diminui o tempo de retenção celular, assim como eventuais diferenças de temperatura.
ABSTRACT The type of material used as packing in anaerobic filters may be a determinant factor in the treatment efficiency, so the evaluation of new materials is important. Thus, the objective of this study was to study the behavior of three upflow anaerobic filters, filled with charcoal, clay pottery and tire rubber, in the treatment of synthetic wastewater with glucose as substrate. The filter, in bench scale (1.3 L), was operated at a HRT of 8 and 4 hours, in two phases. The performance of the filters, in terms of pH, total alkalinity and bicarbonate and volatile acids was stable during the two operational phases. The best filter in terms of COD removal efficiency was the one with activated carbon, 94 and 81%, in Phases I and II, respectively, followed by tire rubber filter, 88 and 63%. The lowest efficiency obtained was the ceramic clay filter, with 81 and 61%, in Phases I and II, respectively. The main morphologies found were bacilli, cocci, filaments, Methanosaeta sp. and Methanosarcina sp. The differences obtained between filters are related to the different characteristics of each material, and the differences between phases are due to the hydraulic load increase and subsequent cellular retention time decrease, as well as an eventual temperature difference.
RESUMO
RESUMO Compreender o comportamento hidrodinâmico de reatores biológicos pode auxiliar na detecção de problemas associados a falhas operacionais e de projeto, situações que prejudicam a eficiência do tratamento. Neste artigo, realizaram-se simulações da fluidodinâmica computacional (CFD) de escoamento de duas fases sólida-líquida de um reator anaeróbio de manta de lodo e fluxo ascendente (UASB), em escala piloto (160 L), com tempo de detenção hidráulica (TDH) de 10 h e vazão de 16 L.h-1. Um modelo Euler-Euler simplificado foi formulado para simular o comportamento hidrodinâmico da zona de reação, influenciada pela configuração do sistema de distribuição do afluente. Foram avaliadas quatro configurações do sistema de distribuição do afluente no reator: uma entrada na parte central (1) e duas entradas centrais (2), de fluxo ascendente; duas entradas nas laterais (3), de fluxo radial; e três entradas de fluxo descendente (4), utilizando geometrias bidimensionais e tridimensionais para verificar a formação de zonas mortas, curtos-circuitos hidráulicos e caminhos preferenciais. As melhores características hidrodinâmicas e a melhor distribuição do afluente foram verificadas na configuração 4, com melhor perfil de mistura do lodo com a fase líquida, na comparação com as demais configurações. Foi notada formação de vórtices na parte inferior do reator com maior concentração do lodo anaeróbio nessa configuração e de caminhos preferenciais nas laterais do reator na configuração 3, indicando mistura ineficiente do afluente com o lodo anaeróbio. O modelo demonstrou que a configuração do sistema de distribuição do afluente influencia significativamente o comportamento hidrodinâmico do reator UASB.
ABSTRACT Understanding the hydrodynamics behavior of biological reactors can help in the detection of problems related to operational failures and design that adversely affect the efficiency of the treatment. In this paper, computational fluid dynamics (CFD) simulations of two-phase liquid-solid flow were carried out in an upflow anaerobic sludge blanket reactor in pilot scale (160 L), with hydraulic retention time (HRT) of 10 h and flowrate 16 L.h-1. The Euler-Euler approach was formulated to simulate the reaction zone hydrodynamics. Four configurations of the influent distribution system in the reactor were evaluated: one central inlet (1) and two central inlets (2), upflow; two lateral inlets (3), radial flow; and three inlets, downflow (4), using two and three-dimensional geometries to verify the formation of dead zones, hydraulic short-circuiting and preferential pathways. Better influent distribution and greater mixture profile of the sludge with the liquid phase were found in the configuration 4, compared to the others by the formation of vortices in the bottom part of the reactor with higher concentration of anaerobic sludge. Formation of preferential pathways was noted in the lateral inlets of the reactor in the configuration 3, indicating an inefficient mixture of the influent with the sludge. The model demonstrates that the configuration of the influent distribution system significantly influences the hydrodynamics behavior of the UASB reactor.
RESUMO
Um reator UASB em escala piloto (160 l) foi usado com o objetivo de estudar seu comportamento hidrodinâmico quando submetido a variações cíclicas senoidais da vazão afluente. Os ensaios foram realizados com traçador eosina Y para as condições operacionais: vazão média afluente constante e igual a 16 l.h-1 e tempo de detenção hidráulica de 10 h (ensaios 1 e 2), e para vazão afluente submetida à variação senoidal de 40 por cento (ensaios 3 e 4) e de 60 por cento (ensaio 5). A variação da concentração do traçador no efluente foi ajustada pelos modelos teóricos de dispersão de fluxo e de reatores em série. O reator UASB apresentou comportamento similar ao de reator de mistura completa para vazão média afluente constante e similar ao reator de fluxo pistonado com a aplicação das variações senoidais cíclicas, sendo que o modelo de pequena dispersão apresentou melhor ajuste matemático.
A bench scale UASB reactor (160 l) was used in stimulus-response assays in order to evaluate its behaviour when submitted to cyclical sinusoidal variations of the influent flow rate. Assays were carried out with eosin Y as the tracer in different operational conditions: constant mean influent flow rate of 16 l.h-1 and hydraulic residence time of 10 h (assays 1 and 2), and influent flow rate submitted to sinusoidal variation of 40 percent (assays 3 and 4) and 60 percent (assay 5). The variation of tracer concentration in the effluent was adjusted by the theoretical models of dispersion (low and high) and N-continuous stirred tank reactors in series. Complete mixture behaviour was noted to the application of the constant influent flow rate and a plug flow one to the application of the cyclical sinusoidal variations of the influent flow rate. The low dispersion model demonstrated the best mathematical adjustment in the RTD.