RESUMO
When restoring anterior teeth using resin composites, the use of silicone guide matrices obtained from diagnostic wax-ups is recommended, as this technique facilitates layering and optimizes working time. This is particularly important in polychromatic layering and when more than one anterior tooth is to be restored with resin composites. However, in cases of fractured anterior teeth, it is often not feasible to perform a previous impression and waxing. In these cases, due to trauma and related psychological aspects, patients usually seek immediate esthetic solutions. Therefore, an interesting restorative approach that can simplify the restorative technique is the creation of a silicone guide matrix obtained from the patient's fractured tooth, without the need for prior waxing. This type of personalized matrix was initially proposed by Bertholdo, Ricci, and Barrote. Thus, the purpose of the present work is to demonstrate a modification of the technique for making this type of custom-made matrix for the restoration of two upper central incisors of a 14-year-old patient who fractured his teeth in a bicycle accident.
Assuntos
Restauração Dentária Permanente , Fraturas dos Dentes , Humanos , Adolescente , Restauração Dentária Permanente/métodos , Resinas Compostas/uso terapêutico , Fraturas dos Dentes/terapia , Incisivo/lesões , Assistência OdontológicaRESUMO
In this study, an acrylamide-based adhesive was combined with a thiourethane-based composite to improve bond stability and reduce polymerization stress, respectively, of simulated composite restorations. The stability testing was conducted under physiologic conditions, combining mechanical and bacterial challenges. Urethane dimethacrylate was combined with a newly synthesized triacrylamide (TMAAEA) or HEMA (2-hydroxyethyl-methacrylate; control) to produce a 2-step total-etch adhesive system. Methacrylate-based composites (70 wt% silanized filler) were formulated, containing thiourethane oligomers at 0 (control) or 20 wt%. Standardized preparations in human third molars were restored; then, epoxy replicas were obtained from the occlusal surfaces before and after 7-d storage in water or with Streptococcus mutans biofilm, which was tested after storage in an incubator (static) or the bioreactor (mechanical challenge). Images were obtained from the replicas (scanning electron microscopy) and cross sections of the samples (confocal laser scanning microscopy) and then analyzed to obtain measurements of gap, bacterial infiltration, and demineralization. Microtensile bond strength of specimens stored in water or biofilm was assessed in 1-mm2 stick specimens. Data were analyzed with analysis of variance and Tukey's test (α = 0.05). HEMA-based materials had greater initial gap measurements, indicating more efficient bonding for the acrylamide materials. When tested in water, the triacrylamide-based adhesive had smaller gaps in the incubator or bioreactor. In the presence of biofilm, there was less difference among materials, but the acrylamide/thiourethane combination led to statistically lower gap formation in the bioreactor. HEMA and TMAAEA-based adhesives produced statistically similar microtensile bond strengths after being stored in water for 7 d, but after the same period with biofilm-challenged specimens, the TMAAEA-based adhesives were the only ones to retain the initial bond strength values. The use of a stable multiacrylamide-based adhesive led to the preservation of the resin-dentin bonded interface after a physiologically relevant challenge. Future studies will include a multispecies biofilm model.
Assuntos
Colagem Dentária , Adesivos Dentinários , Acrilamidas , Resinas Compostas/química , Cimentos Dentários/química , Dentina , Adesivos Dentinários/química , Humanos , Teste de Materiais , Metacrilatos/química , Cimentos de Resina/química , Resistência à Tração , ÁguaRESUMO
OBJECTIVE: To evaluate, through the application of different dentin bonding systems, the influence of wetness on shear bond strength in enamel. METHODS: This study evaluated three etch-and-rinse adhesive systems (Scotchbond MP [used with and without primer]; Singlebond; and Prime&Bond 2.1) and two self-etching adhesive systems (Clearfil SE Bond; and Xeno IV). Flat bovine enamel surfaces were either air-dried for 30 seconds or blotted with absorbent paper after acid-etching for the conventional bonding agents or before the application of self-etching bonding agents. The resin composite EsthetX was bonded to flat surfaces that had been treated with one of the adhesives, following the manufacturer's instructions. After being stored in water at 37°C for one week, bonded specimens were broken in shear. Data were evaluated with two-way analysis of variance (ANOVA) and Student-Newman-Keuls tests (α=0.05). For comparing each condition individually, regardless of the adhesive or wetness condition, a one-way ANOVA and a Student-Newman-Keuls test (α=0.05) were applied. RESULTS: The two-way ANOVA showed significant differences among adhesive systems. An interaction effect was also observed (p<0.05), but wetness did not influence shear bond strength (p=0.98). The one-way ANOVA showed that the all-in-one adhesive was the only material influenced by the presence of water at the enamel's surface. CONCLUSION: The all-in-one adhesive behaved differently depending on whether the enamel surface was dry or wet.