RESUMO
Abstract Life cycle assessment was carried out for a conventional wooden furniture set produced in Mardan division of the Khyber Pakhtunkhwa province of Pakistan during 2018-19. Primary data regarding inputs and outputs were collected through questionnaire surveys from 100 conventional wooden furniture set manufacturers, 50 in district Mardan and 50 in district Swabi. In the present study, cradle-to-gate life cycle assessment approach was applied for a functional unit of one conventional wooden furniture set. Production weighted average data were modelled in the environmental impacts modelling software i.e., SimaPro v.8.5. The results showed that textile used in sofa set, wood preservative for polishing and preventing insects attack and petrol used in generator had the highest contribution to all the environmental impact categories evaluated. Total cumulative energy demand for wooden furniture set manufactured was 30,005 MJ with most of the energy acquired from non-renewable fossil fuel resources.
Resumo A abordagem de avaliação do ciclo de vida foi realizada para um conjunto de móveis de madeira convencional produzido na divisão Mardan da província de Khyber Pakhtunkhwa do Paquistão durante 2018-19. Os dados primários sobre entradas e saídas foram coletados por meio de pesquisas por questionário de 100 fabricantes de conjuntos de móveis de madeira convencionais, 50 no distrito de Mardan e 50 no distrito de Swabi. No presente estudo, a abordagem de avaliação do ciclo de vida do berço ao portão foi aplicada para uma unidade funcional de um conjunto de móveis de madeira convencional. Os dados da média ponderada da produção foram modelados no software de modelagem de impactos ambientais, isto é, SimaPro v.8.5. Os resultados mostraram que os têxteis usados no conjunto de sofás, o preservativo de madeira para polir e prevenir o ataque de insetos e a gasolina usada no gerador tiveram a maior contribuição em todas as categorias de impacto ambiental avaliadas. A demanda total acumulada de energia para o conjunto de móveis de madeira fabricado foi de 30.005 MJ, com a maior parte da energia adquirida de recursos de combustíveis fósseis não renováveis.
RESUMO
Abstract Life cycle assessment was carried out for a conventional wooden furniture set produced in Mardan division of the Khyber Pakhtunkhwa province of Pakistan during 2018-19. Primary data regarding inputs and outputs were collected through questionnaire surveys from 100 conventional wooden furniture set manufacturers, 50 in district Mardan and 50 in district Swabi. In the present study, cradle-to-gate life cycle assessment approach was applied for a functional unit of one conventional wooden furniture set. Production weighted average data were modelled in the environmental impacts modelling software i.e., SimaPro v.8.5. The results showed that textile used in sofa set, wood preservative for polishing and preventing insects attack and petrol used in generator had the highest contribution to all the environmental impact categories evaluated. Total cumulative energy demand for wooden furniture set manufactured was 30,005 MJ with most of the energy acquired from non-renewable fossil fuel resources.
Resumo A abordagem de avaliação do ciclo de vida foi realizada para um conjunto de móveis de madeira convencional produzido na divisão Mardan da província de Khyber Pakhtunkhwa do Paquistão durante 2018-19. Os dados primários sobre entradas e saídas foram coletados por meio de pesquisas por questionário de 100 fabricantes de conjuntos de móveis de madeira convencionais, 50 no distrito de Mardan e 50 no distrito de Swabi. No presente estudo, a abordagem de avaliação do ciclo de vida do berço ao portão foi aplicada para uma unidade funcional de um conjunto de móveis de madeira convencional. Os dados da média ponderada da produção foram modelados no software de modelagem de impactos ambientais, isto é, SimaPro v.8.5. Os resultados mostraram que os têxteis usados no conjunto de sofás, o preservativo de madeira para polir e prevenir o ataque de insetos e a gasolina usada no gerador tiveram a maior contribuição em todas as categorias de impacto ambiental avaliadas. A demanda total acumulada de energia para o conjunto de móveis de madeira fabricado foi de 30.005 MJ, com a maior parte da energia adquirida de recursos de combustíveis fósseis não renováveis.
Assuntos
Meio Ambiente , Decoração de Interiores e Mobiliário , PaquistãoRESUMO
Life cycle assessment was carried out for a conventional wooden furniture set produced in Mardan division of the Khyber Pakhtunkhwa province of Pakistan during 2018-19. Primary data regarding inputs and outputs were collected through questionnaire surveys from 100 conventional wooden furniture set manufacturers, 50 in district Mardan and 50 in district Swabi. In the present study, cradle-to-gate life cycle assessment approach was applied for a functional unit of one conventional wooden furniture set. Production weighted average data were modelled in the environmental impacts modelling software i.e., SimaPro v.8.5. The results showed that textile used in sofa set, wood preservative for polishing and preventing insects attack and petrol used in generator had the highest contribution to all the environmental impact categories evaluated. Total cumulative energy demand for wooden furniture set manufactured was 30,005 MJ with most of the energy acquired from non-renewable fossil fuel resources.
Assuntos
Meio Ambiente , Decoração de Interiores e Mobiliário , PaquistãoRESUMO
The Asgard superphylum is a deeply branching monophyletic group of Archaea, recently described as some of the closest relatives of the eukaryotic ancestor. The wide application of genomic analyses from metagenome sequencing has established six distinct phyla, whose genomes encode diverse metabolic capacities and which play important biogeochemical and ecological roles in marine sediments. Here, we describe two metagenome-assembled genomes (MAGs) recovered from deep marine sediments off the Costa Rica margin, defining a novel lineage phylogenetically married to "Candidatus Thorarchaeota"; as such, we propose the name "Sifarchaeota" for this phylum. The two Sifarchaeota MAGs encode an anaerobic pathway for methylotrophy enabling the utilization of C1 to C3 compounds (methanol and methylamines) to synthesize acetyl coenzyme A (acetyl-CoA). The MAGs showed a remarkable saccharolytic capabilities compared to other Asgard lineages and encoded diverse classes of carbohydrate active enzymes (CAZymes) targeting different mono-, di-, and oligosaccharides. Comparative genomic analysis based on the full metabolic profiles of different Asgard lineages revealed the close relation between Sifarchaeota and "Candidatus Odinarchaeota" MAGs, which suggested similar metabolic potentials and ecological roles. Furthermore, we identified multiple HGT events from different bacterial donors within Sifarchaeota MAGs, which hypothetically expanded Sifarchaeota capacities for substrate utilization, energy production, and niche adaptation.IMPORTANCE The exploration of deep marine sediments has unearthed many new lineages of microbes. The finding of this novel phylum of Asgard archaea is important, since understanding the diversity and evolution of Asgard archaea may inform also about the evolution of eukaryotic cells. The comparison of metabolic potentials of the Asgard archaea can help inform about selective pressures the lineages have faced during evolution.
Assuntos
Archaea , Genoma Arqueal , Sedimentos Geológicos/microbiologia , Metagenoma , Polissacarídeos/metabolismo , Anaerobiose , Archaea/genética , Archaea/isolamento & purificação , Archaea/metabolismo , Biodegradação Ambiental , Costa Rica , FilogeniaRESUMO
Infrared thermography has been used to help in diagnosing lameness. It is hypothesized that, if used in a routine basis, it could help in understanding musculoskeletal modifications during race training. This study aimed to evaluate thermal variation in the musculoskeletal regions of young Thoroughbred (TB) horses during their initial months of race training. Thermographic examinations were performed once every 2 weeks on 16 (10 male, 6 female) two-year-old TB racehorses, from arrival to the racetrack in June 2016, until January 2017, for a total of 16 evaluations. Thermographic imaging was performed using the appropriate protocol. Temperature (°C) was measured at the dorsal and palmar/plantar aspects of specific regions of interest (fetlock, metacarpal, metatarsal, carpal, tarsal, thoracolumbar, sacroiliac spine, and both hips). Initially, we found a thermal balance and all regions demonstrated a positive correlation with one another. However, a significant difference was noted between the left and right sides as training progressed. Four horses were withdrawn from the study after 50% of evaluations because of metacarpal conditions associated with training. Thermographic examination revealed changes before the clinical manifestation of these conditions. In conclusion, this study demonstrated that infrared thermography is an image technique that can facilitate understanding of musculoskeletal system modifications to race training and should be further investigated as a predictive tool to anticipate the occurrence of lesions.
Assuntos
Ossos Metacarpais , Ossos do Metatarso , Aclimatação , Animais , Feminino , Cavalos , Articulações , Masculino , Termografia/veterináriaRESUMO
Numerous archaeal lineages are known to inhabit marine subsurface sediments, although their distributions, metabolic capacities, and interspecies interactions are still not well understood. Abundant and diverse archaea were recently reported in Costa Rica (CR) margin subseafloor sediments recovered during IODP Expedition 334. Here, we recover metagenome-assembled genomes (MAGs) of archaea from the CR margin and compare them to their relatives from shallower settings. We describe 31 MAGs of six different archaeal lineages (Lokiarchaeota, Thorarchaeota, Heimdallarchaeota, Bathyarcheota, Thermoplasmatales, and Hadesarchaea) and thoroughly analyze representative MAGs from the phyla Lokiarchaeota and Bathyarchaeota. Our analysis suggests the potential capability of Lokiarchaeota members to anaerobically degrade aliphatic and aromatic hydrocarbons. We show it is genetically possible and energetically feasible for Lokiarchaeota to degrade benzoate if they associate with organisms using nitrate, nitrite, and sulfite as electron acceptors, which suggests a possibility of syntrophic relationships between Lokiarchaeota and nitrite and sulfite reducing bacteria. The novel Bathyarchaeota lineage possesses an incomplete methanogenesis pathway lacking the methyl coenzyme M reductase complex and encodes a noncanonical acetogenic pathway potentially coupling methylotrophy to acetogenesis via the methyl branch of Wood-Ljungdahl pathway. These metabolic characteristics suggest the potential of this Bathyarchaeota lineage to be a transition between methanogenic and acetogenic Bathyarchaeota lineages. This work expands our knowledge about the metabolic functional repertoire of marine benthic archaea.
Assuntos
Archaea/isolamento & purificação , Archaea/metabolismo , Sedimentos Geológicos/microbiologia , Archaea/classificação , Archaea/genética , Bactérias/classificação , Bactérias/genética , Bactérias/isolamento & purificação , Bactérias/metabolismo , Carbono/metabolismo , Ciclo do Carbono , Costa Rica , Sedimentos Geológicos/química , Metagenoma , FilogeniaRESUMO
The objective of the study was to analyze the surface area (SA) of the wear caused by simulated chewing on human enamel and opposing restorative material, namely: composite resin (CR), porcelain fused to metal (PFM), lithium disilicate (LD), or monolithic zirconia (MZr). Forty-eight premolars were selected as enamel specimens and divided randomly into 4 groups (n = 48; n =12) used as antagonists in chewing simulation (250,000 loading cycles) against one of the four selected test materials. Enamel and material specimens were scanned and evaluated under digital microscope, and wear SA (mm2) were recorded. Descriptive statistics, paired t-test, one-way ANOVA, and post-hoc Tukey-HSD tests were used for statistics (p < 0.05). The smallest and largest SA were exhibited by enamel against LD (0.80 mm2) and PFM (1.74 mm2), respectively. PFM (3.48 mm2) showed the largest SA and CR (2.28 mm2) showed the smallest SA. Paired t-test for SA values showed significant difference (p < 0.05) in all wear comparisons between materials and enamel antagonists. The wear of materials were greater than that of their respective enamel antagonists (p < 0.05). One-way ANOVA of the logarithmic means of wear SA revealed significant differences (P<0.05). Post-hoc Tukey test revealed significance for PFM (p < 0.05) with other materials. Wear of all test materials was greater compared to the wear of enamel antagonists. PFM and LD caused the largest and the smallest enamel wear, respectively. CR, LD, and MZr are more resistant than PFM to wear after simulated chewing against enamel.
Assuntos
Resinas Compostas/química , Esmalte Dentário/química , Porcelana Dentária/química , Mastigação , Ligas Metalo-Cerâmicas/química , Desgaste dos Dentes/etiologia , Zircônio/química , Adolescente , Adulto , Análise de Variância , Polimento Dentário/métodos , Humanos , Processamento de Imagem Assistida por Computador , Teste de Materiais , Microscopia/instrumentação , Valores de Referência , Estatísticas não Paramétricas , Propriedades de Superfície , Adulto JovemRESUMO
Abstract: The objective of the study was to analyze the surface area (SA) of the wear caused by simulated chewing on human enamel and opposing restorative material, namely: composite resin (CR), porcelain fused to metal (PFM), lithium disilicate (LD), or monolithic zirconia (MZr). Forty-eight premolars were selected as enamel specimens and divided randomly into 4 groups (n = 48; n =12) used as antagonists in chewing simulation (250,000 loading cycles) against one of the four selected test materials. Enamel and material specimens were scanned and evaluated under digital microscope, and wear SA (mm2) were recorded. Descriptive statistics, paired t-test, one-way ANOVA, and post-hoc Tukey-HSD tests were used for statistics (p < 0.05). The smallest and largest SA were exhibited by enamel against LD (0.80 mm2) and PFM (1.74 mm2), respectively. PFM (3.48 mm2) showed the largest SA and CR (2.28 mm2) showed the smallest SA. Paired t-test for SA values showed significant difference (p < 0.05) in all wear comparisons between materials and enamel antagonists. The wear of materials were greater than that of their respective enamel antagonists (p < 0.05). One-way ANOVA of the logarithmic means of wear SA revealed significant differences (P<0.05). Post-hoc Tukey test revealed significance for PFM (p < 0.05) with other materials. Wear of all test materials was greater compared to the wear of enamel antagonists. PFM and LD caused the largest and the smallest enamel wear, respectively. CR, LD, and MZr are more resistant than PFM to wear after simulated chewing against enamel.
Assuntos
Humanos , Adolescente , Adulto , Adulto Jovem , Zircônio/química , Ligas Metalo-Cerâmicas/química , Resinas Compostas/química , Esmalte Dentário/química , Porcelana Dentária/química , Desgaste dos Dentes/etiologia , Mastigação , Valores de Referência , Propriedades de Superfície , Processamento de Imagem Assistida por Computador , Teste de Materiais , Análise de Variância , Estatísticas não Paramétricas , Polimento Dentário/métodos , Microscopia/instrumentaçãoRESUMO
We report a case of primary acquired corneal melanosis without atypia associated with corneal haze in a patient with a history of limbal malignant melanoma and the effect of mitomycin-C. A 75-year-old woman with a history of limbal malignant melanoma presented with loss of vision in right eye. Corneal examination showed a patchy melanotic pigmentation with a central haze. Topical mitomycin-C improved visual acuity and corneal haze. However, the pigmented lesions persisted, and they were removed with alcohol corneal epitheliectomy. Histopathological examination demonstrated primary acquired melanosis without atypia. The lesions were successfully removed, and there were no recurrences during the follow-up period of 36 months. The association of conjunctival and corneal melanosis without atypia is a rare condition. In addition, co-existence of central corneal haze and melanosis may decrease visual acuity. Topical mitomycin-C and alcohol corneal epitheliectomy can be useful treatments in this condition.