RESUMO
This study focused on evaluating the sensitivity and limitations of the simplified equipment used in the Digital Image Correlation (DIC) technique, comparing them with the analog extensometer, based on the mechanical property data of a composite made of fiberglass and epoxy resin. The objectives included establishing a methodology based on the literature, fabricating samples through manual lamination, conducting mechanical tests according to the ASTM D3039 and D3518 standards, comparing DIC with the analog extensometer of the testing machine, and contrasting the experimental results with classical laminate theory. Three composite plates with specific stacking sequences ([0]3, [90]4, and [±45]3) were fabricated, and samples were extracted for testing to determine tensile strength, modulus of elasticity, and other properties. DIC was used to capture deformation fields during testing. Comparisons between data obtained from the analog extensometer and DIC revealed differences of 11.1% for the longitudinal modulus of elasticity E1 and 5.6% for E2. Under low deformation conditions, DIC showed lower efficiency due to equipment limitations. Finally, a theoretical analysis based on classical laminate theory, conducted using a Python script, estimated the longitudinal modulus of elasticity Ex and the shear strength of the [±45]3 laminate, highlighting a relative difference of 31.2% between the theoretical value of 7136 MPa and the experimental value of 5208 MPa for Ex.
RESUMO
Natural fiber composites have been extensively studied for structural applications, with recent exploration into their potential for various uses. This study investigates the impact of chemical treatments on the properties of Brazilian jute woven fabric/polyester resin composites. Sodium hydroxide, hydrogen peroxide, and peracetic acid were utilized to treat the jute fabrics, followed by resin transfer molding (RTM) to form the composites. Evaluation included water absorption, flexural strength, tensile strength, and short-beam strength. The alkaline treatment induced changes in the chemical composition of the fibers' surface. Chemical treatments resulted in increased flexural and short-beam strength of the composites, with no significant alterations in tensile properties. The hydrogen peroxide treatment exhibited lower water absorption, suggesting its potential as a viable option for enhancing the performance of these composites.
RESUMO
Prepregs are commonly fabricated with non-renewable petroleum-based materials. To reduce the impact of the manufacturing of these materials and to produce more sustainable prepregs, this research aims to manufacture poly(furfuryl alcohol)/wood veneer prepregs and their posterior molding in laminate composites. For this purpose, the vacuum infusion process was used to impregnate the wood veneers, and compression molding was applied to manufacture three- and four-layer laminate composites. Scanning electronic microscopy was used to evaluate the impregnation. the laminate manufacturing and differential scanning calorimetry were used to predict the shelf-life of the prepregs, Fourier-transform infrared was used to evaluate the induced hydrolysis resistance, and thermogravimetric analysis was used to determine the thermal degradation of the laminates. Moreover, water uptake and flexural, compressive, and tensile properties were evaluated. The kinetic models were effective and showed a shelf life for the laminates of approximately 30 days in storage at -7 °C, which is an interesting result for laminates with lignocellulosic materials. FTIR proved the laminates' excellent resistance to hydrolysis. The water absorption, thermal stability, and mechanical properties did not differ as the amount of wood veneer increased, but these results were up to ~40% higher compared with unidirectional wood laminates found in the literature, which is probably linked to the excellent interface observed with SEM.
RESUMO
Pine seed shells and yerba mate are common wastes leftover from the food and beverage industry. This study presents the development of rigid polyurethane foams (RPUFs) filled with pine seed shells and yerba mate at 5, 10 and 15 wt%. The fillers were characterized for chemical properties using bench chemistry analyses, and the RPUFs were investigated in terms of chemical, morphological, mechanical, thermal and colorimetric characteristics. The main results indicated that yerba mate showed good compatibility with the polyurethane system, probably because its available hydroxyl groups reacted with isocyanate groups to form urethane bonds, producing increases in mechanical and thermal properties. However, pine seed shell did not appear to be compatible. Anisotropy increased slightly, as there was an increase in the percentage of reinforcement. The mechanical properties of the yerba mate reinforced foams proved stable, while there was a loss of overall up to ~50% for all mechanical properties in those reinforced with pine seed shell. Thermal properties were improved up to ~40% for the yerba mate reinforced foams, while those reinforced with pine nuts were stable. It was possible to observe a decrease in the glass transition temperature (Tg) of ~-5 °C for the yerba mate reinforced foams and ~-14 °C for the pine seed shell reinforced ones.
RESUMO
Four imidazolium-based ionic liquids (IL; 1-butyl-3-methylimidazolium chloride, 1-carboxymethyl-3-methylimidazolium chloride, 1,3-dicarboxymethylimidazolium chloride and 1-(2-hydroxyethyl) -3-methylimidazolium chloride) were tested as compatibilizers of microcrystalline cellulose (MCC). Subsequently, ethanolic IL solutions were prepared; MCC was mixed, and the mixtures were left to evaporate the ethanol at ambient conditions. These modified MCC were characterized and applied as reinforcements (5.0 and 10 phr) in an epoxy resin aiming to manufacture biobased composites with enhanced performances. The IL did not significantly modify the morphological and structural characteristics of such reinforcements. Regarding the thermal stability, the slight increase was associated with the MCC-IL affinity. The IL-modified MCC-epoxy composites presented improved mechanical responses, such as flexural strength (≈22.5%) and toughness behavior (≈18.6%), compared with pure epoxy. Such improvement was also obtained for the viscoelastic response, where the storage modulus at the glassy state depended on the MCC amount and IL type. These differences were associated with stronger hydrogen bonding between IL and epoxy hardener or the IL with MCC, causing a "bridging" effect between MCC and epoxy matrix.
RESUMO
Sandwich panels (SP) are very promising components for structures as they ally high levels of specific stiffness and strength. Civil, marine and automotive industries are some examples of the sectors that use SPs frequently. This work demonstrates the potential of manufacturing Z-pin-reinforced foam core SPs, using a design strategy that indicated optimal values for both pin position and angle, keeping the same pin diameter as determined in a previous study. A simple search algorithm was applied to optimize each design, ensuring maximum flexural stiffness. Designs using optimal pin position, optimal pin angle and optimal values for both parameters are herein investigated using numerical and experimental approaches. The optimal pin position yielded an increase in flexural stiffness of around 8.0% when compared to the non-optimized design. In this same comparison, the optimal pin angle by itself increased the flexural stiffness by about 63.0%. Besides, the highest increase in the maximum load was found for those composites, molded with optimized levels of pin position and pin angle, which synergistically contributed to this result. All results were demonstrated with numerical and experimental results and there was a good agreement between them.