RESUMO
This review reports the use of zeolites in biological processes such as anaerobic digestion, nitrification, denitrification and composting, review that has not been proposed yet. It was found that aerobic processes (activated sludge, nitrification, Anammox) use zeolites as ion-exchanger and biomass carriers in order to improve the seattlebility, the biomass growth on zeolite surface and the phosphorous removal. In the case of anaerobic digestion and composting, zeolites are mainly used with the aim of retaining inhibitors such as ammonia and heavy metals through ion-exchange. The inclusion of zeolite effect on mathematical models applied in biological processes is still an area that should be improved, including also the life cycle analysis of the processes that include zeolites. At the same time, the application of zeolites at industrial or full-scale is still very scarce in anaerobic digestion, being more common in nitrogen removal processes.
Assuntos
Zeolitas , Reatores Biológicos , Desnitrificação , Nitrificação , Nitrogênio , Esgotos , Resíduos Sólidos , Águas ResiduáriasRESUMO
The results of total ammoniacal nitrogen (NH(3) + NH(4) (+)) removal in aquaculture systems using two experimental sets, aquatic seedlings produced in laboratory controlled conditions and wild seaweed (Macrocystis spp.) in reproductive state, are shown in this work. Biofiltration assays were carried out using a load of total ammoniacal nitrogen (TAN) of 1 mg/L. Absorption rates were measured taking into account a previous surface characterization, which gave values of 44 ± 14 cm(2)/g and 18 ± 6 cm(2)/g for aquatic seedlings and wild algae, respectively. The following parameters were measured during the experimental runs: temperature, pH, O(2), illuminance or light intensity, salinity and total solids. TAN removals of 61% and 70% were achieved for the seedlings and Macrocystis spp., respectively, after 17 h of treatment. The TAN absorption results were expressed as a function of surface and mass achieving the following values: 3.0 nmol N cm(-2) h(-1) and 111 nmol N g(-1) h(-1) for the seedlings, and 6.9 nmol N cm(-2) h(-1) and 122.4 nmol N g(-1) h(-1) for the macroalgae. In the light of these biofiltration processes, the initial TAN concentration decreased by 90% for the seedlings and wild algae over approximately 110 and 41 h, respectively. In addition, TAN removals achieved with Macrocystis spp. were always higher than those obtained with aquatic seedlings for the same operating periods.
Assuntos
Amônia/química , Macrocystis/metabolismo , Nitrogênio/isolamento & purificação , Eliminação de Resíduos Líquidos/métodos , Poluentes Químicos da Água/química , Amônia/metabolismo , Aquicultura , Filtração , Concentração de Íons de Hidrogênio , Salinidade , Temperatura , Poluentes Químicos da Água/metabolismoRESUMO
The main objective of this work was to evaluate the influence of the food to microorganisms (F/M) ratio and temperature on batch anaerobic digestion processes carried out with and without zeolite addition as a microbial carrier. Three laboratory-scale experimental runs were conducted using a synthetic substrate with a COD:N:P ratio of 500:5:1. The first run (I) was conducted at a constant temperature of 27°C, increasing the F/M ratio from 0.21 to 0.40 (g COD/g VSS). During the second run (II) the temperature and the F/M ratio increased from 27°C to 37°C and from 0.21 to 0.40, respectively. Finally, in the third experimental run (III) the F/M ratio achieved high values (1.92 and 1.30) either by varying the substrate concentration at a constant biomass concentration or by increasing the biomass concentration at a constant substrate concentration. Higher biomass growth rate, COD removal and methane production were found in the reactors with zeolite, especially at the highest F/M assayed during the first run. The highest ammonium removals were also achieved at the highest F/M ratio (0.40) in the reactors with zeolite. Within the range studied (25°C-37°C) in the reactors with zeolite operating at 37°C, the second run demonstrated the low influence of temperature on substrate consumption and ammonia removal, with 93% and 70% of COD and ammonia removal efficiencies, respectively. The third run corroborated the results previously obtained and fit the experimental results to simple kinetic models, the Monod model being the most adequate for predicting the behavior of the systems studied. The maximum specific microorganism growth rate (µ(max)) values for the reactors with zeolite were almost twice as high as those obtained for the reactors without zeolite for similar F/M ratios.
Assuntos
Reatores Biológicos/microbiologia , Eliminação de Resíduos Líquidos/métodos , Zeolitas/química , Anaerobiose , Biodegradação Ambiental , Cinética , TemperaturaRESUMO
An evaluation of natural zeolite as a microorganism carrier in nitrifying reactors operated in batch mode was carried out. Specifically, the influence of zeolite particle sizes of 0.5, 1.0 and 2.0 mm in diameter on microorganism adherence to zeolite, ammonium adsorption capacity and the identification of microbial populations were assessed. The greatest amount of total biomass adhered was observed for a zeolite particle size of 1 mm (0.289 g) which was achieved on the 12th day of operation. The highest ammonium adsorption capacity was observed for a zeolite particle size of 0.5 mm, which was 64% and 31% higher than that observed for particle sizes of 1.0 and 2.0 mm, respectively. The maximum de-sorption values were also found for a zeolite particle size of 0.5 mm, although when equilibrium was reached the ammonium concentrations were similar to those observed for a zeolite particle size of 1.0 mm. It was also found that the experimental data on ammonium adsorption fitted very well to the Freundlich isotherm for the three particle sizes studied. Finally, the nitrifying reactors showed similar microbial populations independently of the particle size used as microorganism carrier. The dominant bacterial community was Gammaproteobacteria making up 80% of the total population found. Betaproteobacteria were also identified and made up 12% approx. of the total population. Ammonium Oxidant Betaproteobacteria and Nitrobacter were also detected.
Assuntos
Bactérias/isolamento & purificação , Compostos de Amônio Quaternário/química , Zeolitas/química , Adsorção , Bactérias/classificação , Carga Bacteriana , Reatores Biológicos , Tamanho da Partícula , EsgotosRESUMO
Natural and modified zeolites (0.5-1.0 mm) from the Tasajera deposit in Cuba were used to enhance the anaerobic digestion process of synthetic substrates. Natural zeolites were modified by ionic exchange and by adsorption with nickel, cobalt and magnesium. The experiments were carried out by using an inoculum from a full-scale anaerobic reactor treating winery wastewater. Modified natural zeolites not only enhanced the anaerobic digestion process, but also increased the specific methanogenic activity (SMA) of the sludges. The textural and chemical surface characteristics of the modified zeolites were related to the process performance, volatile fatty acid (VFA) production and microbial communities found in the digesters. For the selected dose of modified zeolites [0.05 g/g of volatile suspended solids (VSS)], the lowest concentration was found for cobalt followed by nickel and magnesium. Based on the analyses of anaerobic biofilms, the heavy metal incorporated into the zeolite was shown to have a great influence on the predominance of species. For example, the presence of nickel and cobalt favoured Methanosaeta, while at the same dose magnesic zeolite stimulated the presence of Methanosarcina and sulfate-reducing bacteria (SRB). In digesters with modified zeolites and metal supplementations the values of SMA were higher than those obtained in the control and natural zeolite digesters.
Assuntos
Bactérias/metabolismo , Reatores Biológicos/microbiologia , Metais Pesados/química , Metano/metabolismo , Eliminação de Resíduos Líquidos/métodos , Anaerobiose , Bactérias/classificação , Ácidos Graxos Voláteis/metabolismo , Metais Pesados/análise , Metais Pesados/metabolismo , Fosfatos/metabolismo , Zeolitas/químicaRESUMO
This work presents the effect of ammonia nitrogen concentration and zeolite addition on the specific methanogenic activity (SMA) of different anaerobic sludges with various physical structures (granular and flocculent), operating in batch conditions. Piggery, malting production and urban sludges derived from full-scale anaerobic reactors were tested in the experiment as the source of inoculum in batch digesters. It was found that piggery sludge was the most affected by the increase of ammonia nitrogen concentration while malting producing and municipal sludges were less affected. In general, the addition of zeolite at doses in the range of 0.01-0.1 g/g VSS reduced the inhibitory effect of N-NH(4)(+) for piggery sludge (P.S.). For this sludge, the propionic:acetic ratio increased when the concentration of N-NH(4)(+) increased, indicating that methanogenesis was affected. Finally, a study of the microbial population involved in this study for P.S. by using 16S rRNA based molecular techniques revealed a presence of microorganisms following the order: Methanococcaceae > Methanosarcina > Methanosaeta.
Assuntos
Amônia/toxicidade , Nitrogênio/toxicidade , Esgotos/microbiologia , Zeolitas/toxicidade , Anaerobiose , Archaea/efeitos dos fármacos , Archaea/metabolismo , Bactérias Anaeróbias/efeitos dos fármacos , Bactérias Anaeróbias/metabolismo , RNA Ribossômico 16S/genéticaRESUMO
Winery wastewater was treated in two pilot-scale aerated lagoons operating in fed-batch mode. A first lagoon of 27.2m(3) working volume was gradually filled with wastewater with an average COD content of 8700mg/L. Given that with the flow-rate used (790L/day) this first lagoon completed its working volume after 30days of starting, part of the liquid contained in the first lagoon was transferred to another adjacent second lagoon of 10.8m(3) working volume. Therefore, the experiment continued in the second lagoon for another additional 24days using an influent with a COD content of 18,700mg/L at a flow-rate of 170L/day. After the 21st day, a maximum COD removal efficiency of 91% was achieved, and this value was maintained virtually constant until the end of the experiments. A mathematical model based on three differential equations solved simultaneously allowed the kinetic parameters of the system to be obtained.
Assuntos
Ar , Resíduos Industriais , Poluentes da Água , Vinho , Concentração de Íons de Hidrogênio , Cinética , Oxigênio , Projetos Piloto , TemperaturaRESUMO
A two-phase anaerobic digestion process of synthetic domestic wastewater was studied at ambient temperature in mild to cold climates. The hydrolytic stage was carried out in a continuous stirred tank reactor with an effective volume of 1.2 L. The hydrolytic reactor operated at hydraulic retention times (HRTs) in the range of 1.3 to 2.7 h, which allowed for optimum HRT to be obtained in order to achieve a maximum amount of soluble COD. For the methanogenic stage, an up-flow anaerobic filter with a volume of 1.35 L and corrugated plastic rings as biomass immobilization support were used. During the investigation, the ambient temperature ranged between 21 degrees C and 24 degrees C. Synthetic domestic wastewater with a COD of 700 mg/L was used as substrate. The study was performed at total organic loading rates (OLR(T)) of 2.0-4.3 g COD/L. d, with a global HRT (including both hydrolytic and methanogenic stages) of 2.8-5.8 hours. A maximum percentage of organic matter removed of 88% was achieved at a global HRT of 5.8 hours. Under these operating conditions, the production of biogas was 97% higher than that obtained in the one-phase anaerobic digestion process. Additionally, the kinetics involved in the hydrolytic stage was determined using the Contois kinetic model, which adequately predicted the experimental results.
Assuntos
Anaerobiose , Temperatura , Poluentes da Água/metabolismo , HidróliseRESUMO
The effect of the hydraulic retention time (HRT) on the performance of two up-flow anaerobic fixed bed digesters (UFAFBDs) packed with waste tire rubber (D1) and waste tire rubber and zeolite (D2) as micro-organism immobilization supports was studied. It was found that a first-order kinetic model described well the experimental results obtained. The kinetic constants for COD, BOD5, total solids (TS) and volatile solids (VS) removal were determined to be higher in digester D2 than in digester D1 or control. Specifically, they were 0.28 +/- 0.01, 0.32 +/- 0.02, 0.16 +/- 0.01 and 0.24 +/- 0.01 d(- 1) respectively for D1 and 0.33 +/- 0.02, 0.40 +/- 0.02, 0.21 +/- 0.01 and 0.28 +/- 0.01 d(- 1) respectively for D2. This was significant at the 95% confidence level. In addition, the first-order model was also adequate for assessing the effect of the HRT on the removal efficiency and methane production. Maximum methane yield and the first-order constant for methane production were determined and the results obtained were comparable with those obtained by other authors but operating at higher HRTs. Maximum methane yields and the kinetic constant for methane production were 11.1% and 29.4% higher in digester D2 than in D1.
Assuntos
Anaerobiose , Indústria de Laticínios , Esterco , Zeolitas/química , Reatores Biológicos , CinéticaRESUMO
A study of the anaerobic treatment of wastewaters derived from red (RWWW) and tropical fruit wine (TFWWW) production was carried out in four laboratory-scale fluidized bed reactors with natural zeolite as bacterial support. These reactors operated at mesophilic temperature (35 degrees C). Reactors R1 and R2 contained Chilean natural zeolite, while reactors R3 and R4 used Cuban natural zeolite as microorganism support. In addition, reactors R1 and R3 processed RWWW, while reactors R2 and R4 used TFWWW as substrate. The biomass concentration attached to zeolites in the four reactors studied was found to be in the range of 44-46 g volatile solids (VS)/L after 90 days of operation time. Both types of zeolites can be used indistinctly in the fluidized bed reactors achieving more than 80%-86% chemical oxygen demand (COD) removals for organic loading rates (OLR) of up to at least 20 g COD/L d. pH values remained within the optimal range for anaerobic microorganisms for OLR values of up to 20 and 22 g COD/L d for RWWW and TFWWW, respectively. Toxicity and inhibition levels were observed at an OLR of 20 g COD/L d in reactors R1 and R3 while processing RWWW, whereas the aforementioned inhibitory phenomena were not observed at an OLR of 24 g COD/L d in R2 and R4, treating TFWWW as a consequence of the lower phenolic compound content present in this substrate. The volatile fatty acid (VFA) levels were always lower in reactors processing TFWWW (R2 and R4) and these values (< 400 mg/L, as acetic acid) were lower than the suggested limits for digester failure. The specific methanogenic activity (SMA) was twice as high in reactors R2 and R4 than in R1 and R3 after 120 days of operation when all reactors operated at an OLR of 20 g COD/L d.