RESUMO
This work presents a one-step synthesis methodology for preparing a hydrochar (HC) doped with TiO2 (HC-TiO2) for its application on the degradation of crystal violet (CV) using UV and visible radiation. Byrsonima crassifolia stones were used as precursors along with TiO2 particles. The HC-TiO2 sample was synthesized at 210 °C for 9 h using autogenous pressure. The photocatalyst was characterized to evaluate the TiO2 dispersion, specific surface area, graphitization degree, and band-gap value. Finally, the degradation of CV was investigated by varying the operating conditions of the system, the reuse of the catalyst, and the degradation mechanism. The physicochemical characterization of the HC-TiO2 composite showed good dispersion of TiO2 in the carbonaceous particle. The presence of TiO2 on the hydrochar surface yields a bandgap value of 1.17 eV, enhancing photocatalyst activation with visible radiation. The degradation results evidenced a synergistic effect with both types of radiation due to the hybridized π electrons in the sp2-hybridized structures in the HC surface. The degradation percentages were on average 20% higher using UV radiation than visible radiation under the following conditions: [CV] = 20 mg/L, 1 g/L of photocatalyst load, and pH = 7.0. The reusability experiments demonstrated the feasibility of reusing the HC-TiO2 material up to 5 times with a similar photodegradation percentage. Finally, the results indicated that the HC-TiO2 composite could be considered an efficient material for the photocatalytic treatment of water contaminated with CV.
Assuntos
Violeta Genciana , Raios Ultravioleta , Luz , Titânio/química , CatáliseRESUMO
In this work nanocomposites based on alginate (Alg) and halloysite as a nanotubular clay (Hy) were developed. Characterization techniques reveal that Hy/Alg nanocomposites are cation exchangers with predominantly negative charge density and good thermal stability. The adsorption equilibrium of Cd(II) in aqueous solution onto Hy/Alg nanocomposites revealed that by increasing the mass of halloysite in the nanocomposite, the adsorption capacity diminished significantly due to the halloysite-alginate interactions. Maximum adsorption capacities of 8, 65, 88, and 132 mg/g of Cd(II) were obtained for samples Hy, Hy/Alg 50%, Hy/Alg 95%, and Alg, respectively. In addition, the adsorption equilibrium of Cd(II) on the Hy/Alg bionanocomposites was affected by the pH and temperature of the solution, demonstrating the presence of electrostatic interactions during adsorption and that this is an exothermic process. The controlling mechanism of adsorption was cation exchange influenced by electrostatic forces. The Cd(II) adsorption rate studies were interpreted by the diffusion-permeation model and reveal that the presence of Hy in the structure of the nanocomposites enhances the permeation coefficient, that is, the adsorption rate was increased. The values of the permeation coefficient varied from 1.95 × 10-7 to 8.50 × 10-7 cm2/s for Hy/Alg 50% and from 1.70 × 10-7 to 3.55 × 10-7 cm2/s for Hy/Alg 95%.
Assuntos
Alginatos , Nanocompostos , Argila/química , Adsorção , Alginatos/química , Cádmio , Minerais , Cinética , Concentração de Íons de HidrogênioRESUMO
A molecularly imprinted polymer was developed and evaluated for selective determination of metronidazole (MNZ) in wastewater. This was achieved by using sodium methacrylate as monomer, toluene as porogen, ethylene glycol dimethacrylate as crosslinker, azobisisobutyronitrile as initiator and metronidazole as template molecule to generate the selectivity of the polymer for the compound, as well as non-imprinted polymers were synthesized. Two different polymerization approaches were used, bulk and emulsion and the polymers obtained by emulsion presented higher retention percentages the MIP 2-M presented the higher retention (83%). The performed method, was validated in fortified water, showing linearity from 10 up to 1000 ng/mL; limit of detection and quantification for compound were between 3 and 10 ng/mL, respectively. Finally, the method was applied in samples of a wastewater treatment plant in the city of San Luis Potosí, México, and the concentrations of MNZ in these samples were 84.1-114 ng/mL.
Assuntos
Metronidazol/análise , Impressão Molecular/métodos , Ácidos Polimetacrílicos/síntese química , Águas Residuárias/química , Poluentes Químicos da Água/análise , Adsorção , Limite de Detecção , Metacrilatos/química , México , Nitrilas/química , Ácidos Polimetacrílicos/química , Propriedades de Superfície , Tolueno/químicaRESUMO
The adsorption of the antibiotic metronidazole (MNZ) on activated carbon (F400), activated carbon cloth (ACF), mesoporous activated carbon (CMK-3), and carbon nanotubes (MWCNT) was investigated in this work. The effect of the adsorbent-adsorbate interactions as well as the operating conditions (ionic strength, solution pH, temperature, chemical modification of the adsorbents by HNO3 treatment, and water matrix) on the adsorption capacity were analyzed to substantiate the adsorption mechanism. The adsorption capacity markedly varied as function of the carbon material, decreasing in the following order: F400>ACF>F400-HNO3>CMK-3>MWCNT>MWCNT-HNO3, and depended not only on their surface area and pore size distribution, but also on their chemical nature. The adsorption of MNZ was influenced by the solution pH, but was not significantly affected by the ionic strength and temperature. The adsorption of MNZ was enhanced when the MNZ solutions were prepared using wastewater. Therefore, the electrolytes present in the wastewater cooperated rather than competed with the MNZ molecules for the adsorption sites. Desorption equilibrium data of MNZ on all carbon materials demonstrated that the adsorption was reversible corroborating the weakness of the adsorbent-adsorbate interactions.