RESUMO

AIM: to assess the small-scale 3D printing feasibility and cost estimation of a device for controlled dynamization. MATERIALS AND METHOD: The two-part device previously developed by our research group was printed with a carbon fiber-reinforced nylon filament (Gen3 CarbonX™ PA6+CF, 3DXTECH Additive Manufacturing) by a professional 3D printer (FUNMAT HT, Intamsys). Electricity, material, and labor costs for production in a Brazilian city in the Santa Catarina state were calculated. RESULTS: The devices for controlled dynamization were successfully printed in accordance with the planned design and dimensions. Six out of 38 printed devices presented defects in the bolt hole and were discarded. The average printing time per device was 1.9 h. The average electricity, material, and labor costs per printed device were respectively US$0.71, US$13.55, and US$3.04. The total production cost per device reaches approximately US$20 by adding the average cost of defective devices (15 %). CONCLUSION: 3D printing of the controlled dynamization device is feasible and its cost seems affordable to most healthcare services, which could optimize the consolidation of diaphyseal fractures and reduce treatment time for patients.

Assuntos

RESUMO

Occlusal stabilization splints are the most common treatment for controlling the deleterious effects of sleep bruxism. This study aimed to evaluate the effectiveness of a low-cost, mixed occlusal splint (MOS) compared to that of a rigid splint. A randomized clinical trial was performed on 43 adults of both sexes with possible sleep bruxism and satisfactory dental conditions. They were divided into rigid occlusal splint (ROS) (n = 23) and MOS (n = 20) groups. Masticatory muscle and temporomandibular joint (TMJ) pain intensity (visual analog scale), quality of life (WHOQOL-BREF), indentations in the oral mucosa, anxiety, and depression (HADS), number of days of splint use, and splint wear were evaluated. All variables were evaluated at baseline (T0), 6 months (T6), and 12 months (T12) after splint installation (T0), and splint wear was evaluated at T6 and T12. Student's t-test, Mann-Whitney U test, non-parametric Friedman's analysis of variance for paired samples and pairwise multiple comparisons, Pearson's chi-square test, two-proportion z-test, non-parametric McNemar's and Cochran's Q, and Wilcoxon tests were used (p < 0.05). In both groups, there was a decrease in TMJ pain and pain intensity over time and improvements in the quality of life scores. At T6, there was a higher rate of splint wear in the MOS group than in the ROS group (p = 0.023). The MOS showed a higher rate of wear than the rigid splint but had similar results for the other variables. Therefore, the use of a mixed splint appears to be effective in controlling the signs and symptoms of sleep bruxism.

Assuntos

RESUMO

STATEMENT OF PROBLEM: Little is known about the effect of different composite resin cements on the bond strength of prefabricated and milled glass fiber post-and-cores. PURPOSE: The purpose of this in vitro study was to compare the push-out bond strengths of root dentin and standard, relined, or computer-aided design and computer-aided manufacturing (CAD-CAM) glass fiber post-and-cores luted with conventional, universal, or self-adhesive composite resin cement. MATERIAL AND METHODS: Post spaces were prepared in 90 premolars. Standard and relined prefabricated and CAD-CAM-milled glass fiber post-and-cores were luted with conventional (RelyX ARC; 3M ESPE), universal (RelyX Ultimate; 3M ESPE), and self-adhesive (RelyX U200; 3M ESPE) composite resin cement (n=10). All specimens were thermally aged (5000 cycles at 5°C and 55°C with a 20-second dwell time) and mechanical fatigue (1 000 000 cycles at 2 Hz, 50-N load). The specimens were sectioned perpendicularly to the root long axis into 1-mm-thick sections (apical, middle, and cervical root thirds), the push-out bond strength was determined, and the mode of failure recorded. Data were submitted to the Kruskal-Wallis test followed by the Bonferroni-Dunn multiple comparison test (α=.05). RESULTS: Push-out bond strength values did not differ (P>.05) among posts at the same root thirds. Standard posts showed higher bond strength than CAD-CAM at the apical third for data grouped by composite resin cements (P<.001). The cervical root thirds had higher bond strength than the apical thirds (P<.05). The cervical, middle, and apical root thirds showed decreasing bond strength values for each type of post for data grouped by composite resin cement (P<.001). Adhesive failures at the dentin-cement interface were predominant. CONCLUSIONS: The type of posts and cements did not affect the bond strength of glass fiber posts. The cervical root thirds had better bonding performance than the apical thirds.

Assuntos

RESUMO

Abstract Occlusal stabilization splints are the most common treatment for controlling the deleterious effects of sleep bruxism. This study aimed to evaluate the effectiveness of a low-cost, mixed occlusal splint (MOS) compared to that of a rigid splint. A randomized clinical trial was performed on 43 adults of both sexes with possible sleep bruxism and satisfactory dental conditions. They were divided into rigid occlusal splint (ROS) (n = 23) and MOS (n = 20) groups. Masticatory muscle and temporomandibular joint (TMJ) pain intensity (visual analog scale), quality of life (WHOQOL-BREF), indentations in the oral mucosa, anxiety, and depression (HADS), number of days of splint use, and splint wear were evaluated. All variables were evaluated at baseline (T0), 6 months (T6), and 12 months (T12) after splint installation (T0), and splint wear was evaluated at T6 and T12. Student's t-test, Mann-Whitney U test, non-parametric Friedman's analysis of variance for paired samples and pairwise multiple comparisons, Pearson's chi-square test, two-proportion z-test, non-parametric McNemar's and Cochran's Q, and Wilcoxon tests were used (p < 0.05). In both groups, there was a decrease in TMJ pain and pain intensity over time and improvements in the quality of life scores. At T6, there was a higher rate of splint wear in the MOS group than in the ROS group (p = 0.023). The MOS showed a higher rate of wear than the rigid splint but had similar results for the other variables. Therefore, the use of a mixed splint appears to be effective in controlling the signs and symptoms of sleep bruxism.

RESUMO

The objective of this systematic review was to analyze the quality of the food frequency instruments/scales used in dentistry while considering their psychometric properties. The databases consulted were PubMed (August 7, 2020), Scopus (August 27, 2020), Web of Science (August 27, 2020), Cumulative Index to Nursing and Allied Health Literature (CINAHL) and Dentistry and Oral Sciences Source (via EBSCO) (August 28, 2020), LILACS and BBO (August 25, 2020), gray literature: Proquest (October 1, 2020), Capes Theses Bank (October 1, 2020), Brazilian Digital Library of Theses and Dissertations (October 1, 2020), Google Scholar (October 2, 2020), and proceedings of the International Association for Dental Research (IADR) (October 10, 2020). All databases were updated on December 12, 2022. Articles were initially selected by reading the 6,421 titles and 13 abstracts selected, followed by reading the 8 articles included for full text reading to confirm the eligibility criteria, with the aid of Rayyan software. Databases of the construction and/or validation of instruments/scales for assessing food consumption for use in dentistry (in clinical contexts and/or epidemiological studies), with or without assessment of their psychometric properties, were included. Review studies, letters to editors, and research protocols were excluded. Risk of bias assessment was performed according to the Consensus-Based Standards for the Selection of Health Measurement Instruments (COSMIN) checklist. The extracted data were author, country, instrument language, sample, assessment instrument, instrument structure, type of food, instruments compared with the clinical condition, adaptation of an existing instrument, and psychometric properties evaluated. The selection, risk of bias analysis, and data extraction processes were performed by two independent evaluators. Seven studies were identified. The instruments available in the literature were in English, Japanese, Creole, and Malay. Only one study performed translation and cross-cultural validation of an instrument, whereas the others were construction studies. One study did not assess psychometric properties. Regarding the quality assessment and general classification of the studies by the COSMIN checklist, all were considered "inadequate," with reliability (test-retest) being the most validated psychometric property; only one study carried out the validation of all psychometric properties measured in COSMIN. Regarding the quality of the instruments presented, all the studies were classified as "inadequate" in the general assessment. Advances are needed in the validation process.

Assuntos

RESUMO

STATEMENT OF PROBLEM: Little is known about the fracture strength, retention, and adaptation of post-and-cores fabricated with novel tooth-colored materials by computer-aided design and computer-aided manufacturing (CAD-CAM). PURPOSE: The purpose of this in vitro study was to investigate the fracture strength, pull-out bond strength (POBS), and volume of luting agent of endodontically treated premolars restored with post-and-cores milled from different CAD-CAM materials. MATERIAL AND METHODS: Post spaces were prepared in 80 human premolars in which post-and-cores fabricated with polyetheretherketone (PK; Ceramill PEEK), nanohybrid composite resin (BB; Brava Block), polymer-infiltrated ceramic (EN; VITA Enamic), and fiber-reinforced epoxy resin (GF; Fiber Cad Post & Core) CAD-CAM materials were luted (n=20). All specimens were subjected to thermal aging (3000 cycles at 5 °C and 55 °C with a 20-second dwell time). Half of the specimens were subjected to mechanical fatigue (250 000 cycles at 5 Hz) before fracture strength testing, while the other half was submitted to POBS testing and volume of luting agent measurement. Fracture strength data were analyzed by 1-way ANOVA, while POBS and volume of luting agent data were submitted to Kruskal-Wallis followed by the Bonferroni-Dunn multiple comparison tests. The correlation between POBS and the volume of luting agent was determined by the Spearman test (α=.05). RESULTS: POBS of GF was significantly higher than that for PK (P<.001); however, failure load (P=.160) and volume of luting agent (P=.390) values did not differ. EN showed the highest percentage of catastrophic failures (20%), while PK exhibited only core deformations. POBS and cement film volume were not significantly correlated (P>.05). CONCLUSIONS: Different CAD-CAM materials did not influence the fracture strength and volume of luting agent of post-and-cores. Post-and-cores made with PEEK blocks showed lower bond strength to intracanal dentin than those made with fiber-reinforced epoxy resin blocks. No significant correlation was found between bond strength and the volume of luting agent.

Assuntos

RESUMO

PURPOSE: To evaluate the in vitro marginal integrity of CAD-CAM composite inlays with the proximal box margin relocated with different direct restorative materials before and after thermomechanical aging. METHODS: Standardized 4 mm-wide Class II cavities were prepared in 40 sound human upper molars. The mesial cervical margin was located in enamel (control) and 1 mm occlusal to the cemento-enamel junction (CEJ), while the distal cervical margin was located in dentin (experimental) and 2 mm apical to the CEJ. In the experimental groups (n=10), the distal margins were relocated up to the CEJ level by using a highly viscous conventional glass ionomer cement (Equia Forte), low-viscosity bulk-fill composite (SureFil SDR Flow), highly viscous nanofilled composite (Filtek Supreme XT), or a highly viscous bulk-fill composite (Filtek Bulk Fill). The inlays were milled from CAD-CAM nanohybrid composite blocks (Brava Block) and luted with dual-cure resin cement (Allcem). The specimens were submitted to thermocycling (5-55°C, 7,800 cycles) and fatigue loading (50 N, 1 Hz, 240,000 cycles). Epoxy resin replicas of the margins were obtained before and after aging and evaluated through scanning electron microscopy. The percentage of continuous margin in relation to individual assessable margin was calculated as the marginal integrity. The data were statistically analyzed using Wilcoxon and Kruskal-Wallis tests (α= .05). RESULTS: The marginal integrity before and after aging was not significantly different (P> 0.05). Similarly, no significant differences were observed between margins relocated with different restorative materials in comparison to enamel margins (P> 0.05). CLINICAL SIGNIFICANCE: Cervical margin relocation is a valid protocol to simplify intra-oral scanning and luting of CAD-CAM composite inlays with deep proximal margins. The marginal integrity at deep margins with relocation material was comparable to that of enamel margins.

Assuntos

RESUMO

Aim: To evaluate the efficacy of ultrasonic bath and traditional brushing in the hygiene of complete dentures of dependent residents in long-term care institutions (LTCIs). Methods: A randomized cross-over clinical study was conducted in 17 maxillary complete denture wearers living in LTCIs. Cleaning protocols were brushing or ultrasonic bath, both applied with neutral liquid soap. Biofilm biomass were estimated by MTT reduction assay and specific microbial load (CFU) of Streptococcus spp., Staphylococcus spp. and Candida spp. were quantified by selective and differential culture media. Results: Ultrasound method showed higher percentage reduction of biofilm biomass and specific microbial loads of Streptococcus spp. compared to brushing (p<0.01). Reduction of microbial loads of the other microorganisms were not different between cleaning methods (p>0.05). Conclusions: The ultrasonic bath proved to be a feasible alternative method for the mechanical cleaning of complete dentures in LTCIs

Assuntos

RESUMO

Objective To virtually prototype a device for external circular fixation of long bone fractures with controlled dynamization made of two different materials and predict their mechanical behavior by using the finite element analysis (FEA) method. Method A software was used for 3D modeling two metal parts closely attached by a sliding dovetail joint and a high-density silicone damper. Distinctive FEAs were simulated by considering two different materials (stainless steel or titanium), modes (locked or dynamized) and loading conditions (static/point or dynamic/0.5 sec) with uniform 150 kg axial load on top of the device. Results The finite elements (FEs) model presented 81,872 nodes and 45,922 elements. Considering stainless steel, the maximum stress peak (140.98 MPa) was reached with the device locked under static loading, while the greatest displacement (2.415 × 10 -3 mm) was observed with the device locked and under dynamic loading. Regarding titanium, the device presented the maximum stress peak (141.45 MPa) under static loading and with the device locked, while the greatest displacement (3.975 × 10 -3 mm) was found with the device locked and under dynamic loading. Conclusion The prototyped device played the role of stress support with acceptable deformation in both locked and dynamized modes and may be fabricated with both stainless steel and titanium.

RESUMO

STATEMENT OF PROBLEM: Even without the use of an intraoral scanner, post-and-cores can be obtained by using a part-digital fabrication workflow that requires pattern modeling (direct, indirect, or impression); however, studies on the adaptation of computer-aided design and computer-aided manufacturing (CAD-CAM) composite resin post-and-cores in comparison with metal cast post-and-cores are sparse. PURPOSE: The purpose of this in vitro study was to analyze the adaptation of CAD-CAM composite resin post-and-cores fabricated through a part-digital fabrication workflow and to compare it with that of metal cast post-and-cores fabricated through conventional methods. METHOD AND MATERIALS: Eight extracted human premolars were endodontically treated and prepared for custom post-and-cores. Metal cast post-and-cores were fabricated with Ni-Cr alloy (Fit Cast-Sb Plus; Talmax) and conventional resin pattern modeling methods directly in the root canal (conventional direct modeling) or indirectly in a stone cast (conventional indirect modeling). Composite resin post-and-cores were milled from nanohybrid glass-ceramic composite resin CAD-CAM blocks (Brava Block; FGM) by using the part-digital workflow. A laboratory scanner was used to digitalize polyvinyl siloxane impressions (part-digital scanned impression direct CAD-CAM [PSC]) of the root canals and resin patterns fabricated directly (part-digital direct CAD-CAM [PDC]) or indirectly (part-digital indirect CAD-CAM [PIC]). All post-and-cores were placed in the respectively prepared root canals, scanned with microcomputed tomography, and measured in terms of volume of the cementation space, the luting cement film thickness in each root third, and the apical gap between the apical end of the post-and-cores and remaining gutta percha (apical gap). The groups were compared for each adaptation parameter by using 2-way (volume of the cementation space and apical gap) and 3-way (film thickness) ANOVA, and the Games-Howell multicomparison post hoc test (α=.05). RESULTS: The conventional direct modeling group had lower mean volume of the cementation space than all CAD-CAM composite resin post-and-cores (P<.041). The conventional indirect modeling group had a lower volume of the cementation space mean than PDC (P<.024) but was not significantly different from PIC (P=.577) or PSC (P=.221). Regardless of the fabrication workflow, no differences were observed among the CAD-CAM composite resin post-and-cores (P>.05). At the apical root third, conventional direct modeling and conventional indirect modeling had lower film thickness means than PSC or PDC (P<.05). In the middle third, conventional direct modeling and conventional indirect modeling had lower film thickness means than PDC (P≤.001). At the cervical third, no differences in film thickness means were observed among the groups (P>.05). PDC had a lower apical gap mean than PSC (P=.013), while no significant differences were found for other pair comparisons (P>.05). CONCLUSIONS: Metal post-and-cores had slightly better adaptation than the CAD-CAM composite resin post-and-cores; however, the part-digital fabrication workflow of CAD-CAM composite resin post-and-cores provided adaptation parameters within a clinically acceptable range and is less time consuming.

Assuntos