RESUMO

Landfill gas (LFG) is related to the biochemical processes generating heat and releasing CH4, CO2, and other gases in lower concentrations, which result in environmental impacts and risk of local explosion. Thermal infrared imagery (TIR) is employed to detect CH4 leakage as a risk control approach. However, the challenge for LFG leakage detection using TIR is establishing a relation between the gas flux and the ground temperature. This study evaluates the problem of a heated gas flowing through a porous medium column where the upward surface exchanges heat by radiation and convection to the environment. A heat transfer model that considers the upward LFG flow is proposed, and a sensibility analysis is developed to relate the flux to the ground temperature level in the condition of non-income solar radiation. An explicit equation to predict CH4 fugitive flow as a function of temperature anomalies of the ground was presented for the first time. The results show that the predicted ground surface temperatures are consistent with the literature's experimental observations. Moreover, the model was complementarily applied to a Brazilian landfill, with in situ TIR measurements in an area with a slightly fractured cover. In this field observation, the predicted CH4 flux was around 9025 g m-2 d-1. Model limitations concerning the soil homogeneity, the transient variation of atmospheric conditions or local pressure, and soil temperature difference in low-flux conditions (related to TIR-cameras accuracy) require further validation. Results could help landfill monitoring in conditions of a high-temperature ground anomaly in dry seasons.

Assuntos

RESUMO

OBJECTIVES: To synthesize and characterize brushite particles in the presence of acidic monomers (acrylic acid/AA, citric acid/CA, and methacryloyloxyethyl phosphate/MOEP) and evaluate the effect of these particles on degree of conversion (DC), flexural strength/modulus (FS/FM) and ion release of experimental composites. METHODS: Particles were synthesized by co-precipitation with monomers added to the phosphate precursor solution and characterized for monomer content, size and morphology. Composites containing 20 vol% brushite and 40 vol% reinforcing glass were tested for DC, FS and FM (after 24 h and 60 d in water), and 60-day ion release. Data were subjected to ANOVA/Tukey tests (DC) or Kruskal-Wallis/Dunn tests (FS and FM, alpha: 5%). RESULTS: The presence of acidic monomers affected particle morphology. Monomer content on the particles was low (0.1-1.4% by mass). Composites presented similar DC. For FS/24 h, only the composite containing DCPD_AA was statistically similar to the composite containing 60 vol% of reinforcing glass (without brushite, "control"). After 60 days, all brushite-containing materials showed similar FS, statistically lower than the control composite (p<0.01). Composites containing DCPD_AA, DCPD_MOEP or DCPD_U ("unmodified") showed statistically similar FM/24 h, higher than the control composite. After prolonged immersion, all composites were similar to the control composite, except DCPD_AA. Cumulative ion release ranged from 21 ppm to 28 ppm (calcium) and 9 ppm to 17 ppm (phosphate). Statistically significant reductions in ion release between 15 and 60 days were detected only for the composite containing DCPD_MOEP. SIGNIFICANCE: Acidic monomers added to the synthesis affected brushite particle morphology. After 60-day storage in water, composite strength was similar among all brushite-containing composites. Ion release was sustained for 60 days and it was not affected by particle morphology.

Assuntos

RESUMO

This study describes the synthesis of dicalcium phosphate dihydrate (DCPD) particles in the presence of different ethylene glycol dimethacrylates (EGDMA, ethylene glycol/EG units: 1, 2, 3 or 4) at two monomer-to-ammonium phosphate molar ratios (1:1 and 2:1), as a strategy to develop CaP-monomer particles with improved interaction with resin matrices. Particles displaying high surface areas and organic contents were added to a photocurable BisGMA-TEGDMA resin and the resulting materials were tested for degree of conversion (DC), biaxial flexural strength (BFS), flexural modulus, and ion release. Data were subjected to one-way ANOVA or Kruskal-Wallis/Dunn test (alpha: 0.05). Functionalization with EGDMA derivatives was dependent upon the length of the spacer group and monomer concentration in the synthesis. No differences in DC were observed among materials (p > 0.05). A 39% increase in BFS was obtained with the use of particles with the highest functionalization level compared to non-functionalized particles (p < 0.001). The use of functionalized DCPD reduced flexural modulus in comparison to non-functionalized particles (p < 0.001). Calcium release was similar among materials and remained constant during the experiment, while phosphate release was higher at 7 days in comparison to the remaining weeks (p < 0.001). In conclusion, diethylene glycol dimethacrylate resulted in the highest functionalization levels and the highest BFS among DCPD-containing materials. Ion release was not affected by functionalization. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2018. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 107B: 708-715, 2019.

Assuntos

RESUMO

OBJECTIVE: to verify the effect of the addition of dicalcium phosphate dihydrate (DCPD) particles functionalized with di- or triethylene glycol dimethacrylate (DEGDMA or TEGDMA) on the degree of conversion (DC), post-gel shrinkage (PS), mechanical properties, and ion release of experimental composites. METHODS: Four composites were prepared containing a BisGMA/TEGDMA matrix and 60 vol% of fillers. The positive control contained only barium glass fillers, while in the other composites 15 vol% of the barium was replaced by DCPD. Besides the functionalized particles, non-functionalized DCPD was also tested. DC after 24 h (n = 3) was determined by FTIR spectroscopy. The strain gage method was used to obtain PS 5 min after photoactivation (n = 5). Flexural strength and modulus (n = 10) were calculated based on the biaxial flexural test results, after specimen storage for 24 h or 60 days in water. The same storage times were used for fracture toughness testing (FT, n = 10). Calcium and phosphate release up to 60 days was quantified by ICP-OES (n = 3). Data were analyzed by ANOVA/Tukey test (alpha: 5%). RESULTS: Composites containing functionalized DCPD presented higher DC than the control (p < 0.001). The material containing DEGDMA-functionalized particles showed higher PS than the other composites (p < 0.001). After 60 days, only the composite with DEGDMA-functionalized DCPD presented fracture strength similar to the control, while for flexural modulus only the composite with TEGDMA-functionalized particles was lower than the control (p < 0.001). FT of all composites containing DCPD was higher than the control after 60 days (p < 0.005). Calcium release was higher for the composite with non-functionalized DCPD at 15 days and no significant reductions were observed for composites with functionalized DCPD during the observation period (p < 0.001). For all the tested composites, phosphate release was higher at 15 days than in the subsequent periods, and no difference among them was recorded at 45 and 60 days (p < 0.001). CONCLUSIONS: DCPD functionalization affected all the studied variables. The composite with DEGDMA-functionalized particles was the only material with strength similar to the control after 60 days in water; however, it also presented the highest shrinkage. The presence of DCPD improved FT, regardless of functionalization. DCPD functionalization reduced ion release only during the first 15 days.

Assuntos

RESUMO

OBJECTIVES: This study describes the synthesis of brushite nanoparticles (CaHPO4·2H2O) functionalized with triethylene glycol dimethacrylate (TEGDMA) and their application in dental restorative composites with remineralizing capabilities. METHODS: Nanoparticles were synthesized, with TEGDMA being added to one of the precursor solutions at three different molar ratios (0:1, 0.5:1 and 1:1, in relation to the ammonium phosphate precursor). Then, they were added (10 vol%) to a photocurable dimethacrylate matrix containing 50 vol% of reinforcing glass particles. The resulting composites were tested for degree of conversion, biaxial flexural strength and elastic modulus (after 24h and 28days in water), and ion release (over a 28-day period). Commercial composites (one microhybrid and one microfilled) were tested as controls. RESULTS: The final TEGDMA content in the functionalizing layer was modulated by the molar ratio added to the precursor solution. Functionalization reduced nanoparticle size, but did not reduce agglomeration. Improved mechanical properties were found for the composite containing nanoparticles with higher TEGDMA level in comparison to the composite containing non-functionalized nanoparticles or those with a low TEGDMA level. All brushite composites presented statistically significant reductions in strength after 28 days in water, but only the material with high-TEGDMA nanoparticles retained strength similar to the microhybrid commercial control. Overall, ion release was not affected by functionalization and presented steady levels for 28 days. SIGNIFICANCE: Though agglomeration was not reduced by functionalization, the improvement in the matrix-nanoparticle interface allowed for a stronger material, without compromising its remineralizing potential.

Assuntos

RESUMO

Silver phosphate is a semi-conductor sensitive to UV-Vis radiation (<530nm). Exposure to radiation removes electrons from the oxygen valence shell, which are scavenged by silver cations (Ag+), forming metallic silver (Ag0) nanoparticles. The possibility of silver nanoparticle formation in situ by a photoreduction process was the basis for the application of mixed calcium phosphate/silver phosphate particles as remineralizing and antibacterial fillers in resin-based dental materials. Mixed phosphate particles were synthesized, characterized and added to a dimethacrylate resin in 20% or 30% mass fractions to investigate their efficacy as ion-releasing fillers for dental remineralization and antibacterial activity. The formation of metallic silver nanoparticles after exposure to visible radiation from a dental curing unit (peak emission: 470nm) was demonstrated by particle X-ray diffraction and scanning electron microscopy analysis of the composite fractured surface. Calcium and phosphate release from materials containing the mixed particles were similar to those containing pure CaP particles, whereas Streptococcus mutans colonies were reduced by three orders of magnitude in relation to the control, which can be attributed to silver release. As expected, the optical properties of the materials containing mixed phosphate particles were compromised by the presence of silver. Nevertheless, materials containing mixed phosphate particles presented higher fracture strength and elastic modulus than those with pure CaP particles.

Assuntos

RESUMO

Dicalcium phosphate dihydrate particles functionalized with triethyleneglycol dimethacrylate were synthesized and added to a photocurable mixture of bisphenol-A glycidyl dimethacrylate and triethyleneglycol dimethacrylate with the purpose of developing a resin composite capable of releasing calcium and phosphate ions to foster dental remineralization. Particle functionalization would minimize the deleterious effect of adding low cohesive strength nano-structured particles with no chemical interaction with the organic matrix on the material's mechanical properties. The results showed that calcium release over 28 days was not impaired by particle functionalization. A statistically significant 32% increase in strength was recorded with the use of functionalized dicalcium phosphate dihydrate in comparison to the material containing non-functionalized particles. However, the strength of the unfilled resin was not matched by the composite with functionalized particles. Elastic modulus increased with particle incorporation, regardless of functionalization. Degree of conversion and optical properties (total transmittance and color change/ΔE) of the resin-based materials were not affected by the addition of dicalcium phosphate dihydrate particles (functionalized or not).

RESUMO

OBJECTIVE: To evaluate the strength and ion release of experimental composites containing TEGDMA-functionalized calcium phosphate particles. METHODS: Seven composites containing equal parts (in mols) of BisGMA and TEGDMA and 60vol% of fillers were manipulated. Filler phase was constituted by silanized barium glass and 0% (control), 10% or 20% (volume) of dicalcium phosphate dihydrate (DPCD) particles, either non-functionalized or functionalized with two different TEDGMA contents. DCPD particles were synthesized and characterized by X-ray diffraction (XRD), elemental analysis, surface area and dynamic light scattering. Composites were tested for degree of conversion (DC) by near-FTIR. Biaxial flexural strength (BFS) was determined after 24h and 28days in water. Calcium and phosphate release after 7days was assessed using inductively coupled plasma optical emission spectrometry (ICP-OES). Data were analyzed by ANOVA/Tukey test (alpha:5%). RESULTS: XRD confirmed the crystalline structure corresponding to DCPD. Elemental analysis revealed particles with zero, 14% or 22% TEGDMA, with similar D50 (around 19µm) and surface areas from 3.5 to 11.4m2/g. The presence of DCPD did not reduce DC. After 24h, functionalization (both 14% and 22% TEGDMA) improved composite strength in comparison to non-functionalized DCPD, both at 10% and 20% levels. After 28days, BFS of materials containing 10% functionalized DCPD were statistically similar to the control containing only barium glass. Among composites containing 10% DCPD, particle functionalization with 14% TEGDMA did not jeopardize ion release. SIGNIFICANCE: At 10vol%, the use of TEGDMA-functionalized CaP particles improved composite strength in relation to non-functionalized particles, while maintaining similar ion release levels.

Assuntos

RESUMO

OBJECTIVE: To evaluate the effect of the replacement of barium glass by dicalcium phosphate dihydrate (DCPD) particles on the mechanical properties and degree of conversion (DC) of composites. Additionally, calcium and hydrogen phosphate (HPO4(2-)) release were followed for 28 days. METHODS: Nine composites containing equal parts (in mols) of BisGMA and TEGDMA and 40, 50 or 60 vol% of total filler were manipulated. Filler phase was constituted by silanated barium glass and 0%, 10% or 20% of DCPD particles. DC was determined by near-FTIR. Biaxial flexural strength (BFS) and modulus (E) were tested using the "piston on three balls" method, while fracture toughness (KIc) used the "single edge notched beam" method. Specimens were tested after 24h and 28 days in water. Ion release was determined using inductively coupled plasma optical emission spectrometry (ICP-OES). Data were analyzed by ANOVA/Tukey (DC and ion release) or Kruskal-Wallis/Mann-Whitney (mechanical properties; alpha: 5%). RESULTS: DC was not affected by DCPD. The presence of DCPD reduced BFS for both storage times, while differences in E became evident after 28 days. After 24h, KIc increased with the addition of DCPD; after 28 days, however, KIc decreased only for DCPD-containing composites. Calcium release was similar for both DCPD contents and remained fairly constant during the 28-day period. Overall, HPO4(2-) release was higher at 7 days and did not decrease after 14 days. SIGNIFICANCE: The composite with the highest filler level and 10% DCPD represented the best compromise between mechanical properties after aging in water and ion release.

Assuntos

RESUMO

The study compared ion release from resin-based materials containing calcium orthophosphates. Amorphous calcium phosphate (ACP), dicalcium phosphate anhydrous (DCPA), dicalcium phosphate dihydrate (DCPD), and tricalcium phosphate (ß-TCP) nanoparticles were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), dynamic light scattering (DLS), and surface area (nitrogen adsorption isotherms, BET method). Nanoparticles were added to a dimethacrylate-based resin and materials were tested for degree of conversion (DC) and calcium/phosphate release up to 28 days under pH 5.5 and 7.0. Data were analyzed by ANOVA/Tukey test (alpha: 0.05).The crystallinity of DCPA, DCPD, and ß-TCP were confirmed, as well as the ACP amorphous nature. DCPD and ß-TCP presented larger agglomerates than DCPA and ACP. The surface area of ACP was 5-11 times higher than those of the other nanoparticles. Materials showed similar DC. The material containing ACP released significantly more ions than the others, which released similar amounts of calcium and, in most cases, phosphate. Ion release was not affected by pH. Calcium release decreased between 7 and 21 days, while phosphate levels remained constant after 14 days. In conclusion, ACP higher ion release can be ascribed to its high surface area. DCPA, DCPD, and ß-TCP had similar performances as ion-releasing fillers.

Assuntos