RESUMO

INTRODUCTION: To compare the stress produced on the walls of simulated canals by rotary instruments with varied tip and taper sizes. METHODS: Ninety isotropic transparent blocks, each containing a 60-degree curved canal, were distributed into 18 groups (n = 5) based on the instrument tip (sizes 10, 15, 20, 25, 30, and 35) and taper (sizes 0.02, 0.04, and 0.06). The blocks were fixed in a circular polariscope setup for dark field analysis. A digital camera was employed to capture the real-time birefringence patterns generated by each instrument. Digital image frames, corresponding to the instrument reaching the end of each canal third, were extracted and evaluated by 2 independent observers for the stress generation on canal walls. The data analysis employed a semi-quantitative scale ranging from 0 to 5. Cohen's Kappa coefficient test was used to determine the inter-observer agreement while the results were compared using Kruskal-Wallis test followed by an all-pairwise posthoc procedure (α = 5%). RESULTS: Inter-observer agreement was 0.95. A significant influence of the tip size on stress was observed across the coronal (P = .011), middle (P = .006), and apical (P = .026) thirds. In contrast, taper size did not affect the stress induced at the coronal (P = .509), middle (P = .958), or apical (P = .493) thirds. The variations in tip and taper sizes did not result in a significant stress differences among the thirds (P = .181). CONCLUSIONS: The stress significantly increased across all canal thirds with larger tip sizes of rotary instruments, whereas the taper sizes did not influence the stress when compared to the canal thirds.

Assuntos

RESUMO

PURPOSE: Individuals with isolated GH deficiency (IGHD) due to a mutation in the GHRH receptor gene have a normal life expectancy and above 50 years of age, similar total cognitive performance, with better attention and executive function than controls. Our objectives were to evaluate their brain morphometry and brain aging using MRI. METHODS: Thirteen IGHD and 14 controls matched by age, sex, and education, were enrolled. Quantitative volumetric data and cortical thickness were obtained by automatic segmentation using Freesurfer software. The volume of each brain region was normalized by the intracranial volume. The difference between the predicted brain age estimated by MRI using a trained neuronal network, and the chronological age, was obtained. p < 0.005 was considered significant and 0.005 < p < 0.05 as a suggestive evidence of difference. RESULTS: In IGHD, most absolute values of cortical thickness and regional brain volumes were similar to controls, but normalized volumes were greater in the white matter in the frontal pole and in the insula bilaterally, and in the gray matter, in the right insula and in left Caudate (p < 0.005 for all comparisons) We also noticed suggestive evidence of a larger volume in IGHD in left thalamus (p = 0.006), right thalamus (p = 0.025), right caudate (p = 0.046) and right putamen (p = 0.013). Predicted brain ages were similar between groups. CONCLUSION: IGHD is primarily associated with similar absolute brain measurements, and a set of larger normalized volumes, and does not appear to alter the process of brain aging.

RESUMO

This study evaluated the impact of long-term storage conditions (medium and time) on the development of experimental dentinal microcracks through micro-computed tomography. Sixty freshly extracted premolars were stored in formalin, water, or dry conditions (n = 20) and scanned after 72 h, 30 days, 6 months and 3 years of extraction. The effect of the storage medium and time on the occurrence of dentinal defects was statistically evaluated. A total of 211 000 images were screened revealing the existence of 11 519 slices with dentinal defects. Dry conditions significantly contributed to the development of new defects in all time points. During the 3-year follow-up period, no new defects were detected in the teeth that were stored in water and, in a single tooth, in the formalin group, after 6 months of storage.

Assuntos

RESUMO

AIM: The aim of this study is to compare the stress produced on the internal walls of simulated canals by nine rotary and four reciprocating systems. METHODOLOGY: Sixty-five isotropic transparent blocks containing a 60° curved and tapered simulated canal were selected and distributed into 13 groups (n = 5) according to the preparation system: BioRace, HyFlex EDM, iRaCe, Mtwo, One RECI, ProTaper Next, RaCe EVO, Reciproc, Reciproc Blue, R-Motion, VDW.ROTATE, XP-Endo Rise Shaper, and XP-Endo Shaper. Each resin block was mounted in a vice and a digital camera recorded the entire sequence of each preparation system through a circular polariscope set for dark field analysis. The video frames when each instrument reached the end of the coronal, middle, and apical thirds of the canal were extracted from the recordings and analysed by two independent observers regarding the stress generated on the canal walls using a semi-quantitative evaluation on a 0-5 scale. Intra- and inter-observer agreement were subjected to the Cohen's Kappa coefficient test, whilst the experimental results were compared using Kruskal-Wallis test post hoc pairwise comparisons with Bonferroni correction (α = 5%). RESULTS: The inter- and intra-observer agreement were 0.98 and 1, respectively. Most instruments demonstrated acceptable performance (scores ≤ 2) in all thirds. Other instruments, such as the HyFlex EDM 25.12 (coronal and middle thirds), Reciproc Blue R25 and Reciproc R25 (coronal and apical thirds), R-Motion 30.04 (apical third), and VDW.ROTATE 20.05 (apical third) showed scores higher than 3. Statistical analysis revealed a significant difference amongst the tested systems at the coronal, middle, and apical thirds (p < .05). CONCLUSION: None of the canal instrumentation protocols were stress-free, showing varying levels of stress concentrations. Various factors seemed to influence the magnitude of stress and its distribution pattern on the canal walls. Overall, instruments characterized by a larger taper, lower speed, reciprocating motion, and made of heat-treated NiTi alloy exhibited higher patterns of stress distribution.

RESUMO

INTRODUCTION: This study aimed to evaluate the effects of root canal enlargement on the danger zone (DZ) of mandibular molars. METHODS: Thirty mesial roots of mandibular first molars were scanned in micro-computed tomography (S1). Canals were sequentially enlarged with rotary instruments up to sizes 30/0.04 (S2) and 30/0.06 (S3). The dentin thickness was measured at 0.1-mm intervals after each preparation step (n = 2964 slices). Root level and position of the DZ were also recorded. Data were compared using analysis of variance with Bonferroni pairwise comparison, Cochran's Q method, and Pearson's test (α = 5%). RESULTS: Comparing the specimens before (S1) and after (S2 and S3) preparations showed a significant reduction in the thickness of the DZ (P < .05), as well as between S2 and S3 steps (P < .05). At S1, the DZ was mostly located in the middle third of the root, but after preparation, it shifted toward the coronal direction (P < .05). Both S2 (P = .004, r = 0.508) and S3 (P = .004, r = 0.506) preparation steps showed a positive correlation between canal length and the root level of the DZ. At S1, the DZ was positioned toward the distal and mesial in 73.4% (n = 22) and 26.6% (n = 8) of the specimens, respectively. After S3, the number of specimens with DZ positioned toward the mesial aspect of the root significantly reduced to 3.3% (n = 1), whereas none of the specimens with DZ positioned toward the distal changed its position after root canal enlargements (P > .05). CONCLUSION: Overall, the enlargement of mesial canals of mandibular first molars with final instruments sizes 30/0.04 and 30/0.06 affected the thickness, root level, and position of the DZ.

Assuntos

RESUMO

INTRODUCTION: This study aimed to compare the in vivo accuracy and precision of 3 electronic apex locators (EALs) in determining the position of the major foramen using micro-computed tomographic (micro-CT) technology. METHODS: After access preparation of 23 necrotic or vital teeth from 5 patients, canals were negotiated, and hand files were used to determine the position of the foramen with 3 EALs: Propex Pixi (Dentsply Maillefer, Ballaigues, Switzerland), Woodpex III (Woodpecker Medical Instrument Co, Guilin, China), and Root ZX II (J Morita, Tokyo, Japan). After fixing the silicon stop to the file, teeth were extracted and scanned in a micro-CT device with and without the instrument inserted into the canal. Data sets were coregistered, and the accuracy and precision of the EALs were determined at a tolerance level of ±0.5 mm by measuring the distance from the tip of the instruments to a tangential line crossing the margins of the foramen. Statistical comparisons were performed using Friedman with post hoc related samples sign and Spearman tests (α = 5%). RESULTS: A significant difference was detected comparing the accuracy of Root ZX II (100%), Woodpex III (86.96%), and Propex Pixi (52.17%) (P < .05). There was a lack of significance in the relationship between the pulp status and the accuracy of the tested EALs (P > .05). Propex Pixi was significantly less precise than Root ZX II (P < .05), whereas no difference was found between Woodpex III and Root ZX II or Propex Pixi (P > .05). CONCLUSIONS: EALs presented similar precision, but Woodpex III and Root ZX II showed better accuracy to determine the position of the apical major foramen than Propex Pixi.

Assuntos

RESUMO

AIM: To assess the interfacial adaptation (gap-containing areas) of two root canal sealers (EndoSequence BC Sealer and AH Plus) to a conventional gutta-percha (GP) cone (GP-sealer interface) in oval-shaped canals filled using the single cone technique. METHODOLOGY: Sixteen teeth with oval-shaped canals were selected, scanned in a micro-computed tomographic device, and pair-matched according to the volume, aspect ratio and configuration of root canals. Root canals were then sequentially prepared with WaveOne Gold Primary and Large instruments, followed by filling with WaveOne Large GP points associated with either the premixed calcium-silicate EndoSequence BC Sealer or the epoxy resin-based AH Plus sealer (n = 8 per group) using the single cone technique. After 7 days stored in phosphate-buffered saline solution at 37°C, the specimens were rescanned and the reconstructed images segmented in order to differentiate the filling materials (sealer and GP cone) to the dentine. A total of 453 cross-sectional slices were assessed and categorized according to the presence or absence of gaps at the GP-sealer interface. Mann-Whitney U-test verified the differences between groups and were considered significant at alpha = 5%. RESULTS: Gaps were non-homogenously distributed in two-dimensional axial cross-section images and none of the specimens showed completely gap-free areas along the entire GP-sealer interface. Root canals filled with EndoSequence BC Sealer and AH Plus displayed 171 (37.75%) and 136 (30.02%) slices with gaps in the GP-sealer interface and these frequencies were statistically significant (p = .000). CONCLUSIONS: Although none of the specimens had a gap-free area along the entire GP-sealer interface, oval canals filled with AH Plus showed less gaps than the ones filled with EndoSequence BC Sealer.

Assuntos

RESUMO

Canal filling materials and techniques have been one of the most studied topics in Endodontics. A simple search using the mesh term "root canal filling" in PubMed revealed more than 11 000 articles, an impressive number that is much higher than "root canal disinfection" (5544 articles) or even the popular "root canal preparation" (8527 articles). The overriding importance attributed to root filling procedures is not merely intuitive. It derived from the appealing relevance given by the appearance of the white lines in common radiographs grounded on retrospective clinical data that had identified the quality of a root filling as one of the major causes of treatment failure (lack of healing). Since the publication of the Washington study, impressive efforts have been made for the release of new materials and techniques, as well as, for the development of a plethora of laboratory methods to assess the quality of root filling procedures. This narrative review aims to address and discuss the most relevant laboratory methods to assess the root canal filling. As filling quality improvements have not translated into higher success rates, as reported in longitudinal clinical studies, more than to deliver a simple methodology-based review, this paper aims to present an in-depth critical view on the assessment of laboratory methods used to study the filling materials and techniques. Recent data indicate that the long-term dimensional stability/degradation over time of endodontic sealers plays a central role in the treatment outcome. In this context, laboratory methods should be developed focusing on predicting, at least to some degree, the long-term clinical behaviour of root canal fillings, rather than simply ranking different materials or techniques.

Assuntos

RESUMO

In the last decades, the move of medicine towards minimally invasive treatments is notorious and scientifically grounded. As dentistry naturally follows in its footsteps, minimal access preparation have also becume a trend topic in the endodontic field. This procedure aims to maximize preservation of dentine tissue backed up by the idea that this is an effective way to reduce the incidence of post-treatment tooth fracture. However, with the assessment of the body of evidence on this topic, it is possible to observe some key points (a) the demand for nomenclature standardization, (b) the requirement of specific tools such as ultra-flexible instruments, visual magnification, superior illumination, and three-dimensional imaging technology, (c) minimally invasive treatment does not seem to affect orifice location and mechanical preparation when using adequate armamentarium, but it (d) may impair adequate canal cleaning, disinfection and filling procedures, and also (e) it displays contradictory results regarding the ability to increase the tooth strengthen compared to the traditional access cavity. In spite of that, it is undeniable that methodological flaws of some benchtop studies using extracted teeth may be responsible for the conflicting data, thus triggering the need for more sophisticated devices/facilities and specifically designed research in an attempt to make clear the role of the access size/design on long-term teeth survival. Moreover, it is inevitable that a clinical approach such as minimal endodontic access cavities that demands complex tools and skilled and experienced operators bring to the fore doubts on its educational impact mainly when confronted with the conflicting scientific output, ultimately provoking a cost-benefit analysis of its implementation as a routine technique. In addition, this review discusses the ongoing scientific and clinical status of minimally invasive access cavities aiming to input an in-depth and unbiased view over the rationale behind them, uncovering not only the related conceptual and scientific flaws but also outlining future directions for research and clinical practices. The conclusions attempt to skip from passionate disputes highlighting the current body of evidence as weak and incomplete to guide decision making, demanding the development of a close-to-in situ laboratory model or a large and well-controlled clinical trial to solve this matter.

Assuntos

RESUMO

AIM: To evaluate the influence of traditional and conservative access cavity preparations on the remaining dentine thickness in the coronal third of mesial canals of extracted mandibular molars prepared with reciprocating instruments using micro-computed tomography as the analytical tool. METHODOLOGY: Seventy extracted mandibular molars were scanned at a pixel size of 19 µm. From this initial sample, 20 teeth were selected, pair-matched and distributed into two groups (n = 10) according to the access cavity preparation: traditional (TradAC) or conservative (ConsAC). The root canals were sequentially enlarged with Reciproc Blue R25 (size 25, 0.08v taper) and R40 (size 40, 0.06v taper) instruments. A new scan was performed and the postoperative stacks were coregistered with their respective preoperative datasets. A colour-coded cross sections of the roots were created and used to identify and measure the smallest dentine thickness related to both MB and ML canals at 1.0-mm intervals from the furcation level of up to 5 mm in the apical direction, in both mesial and distal aspects of the roots, before and after preparation. The statistical analyses were performed with paired-samples t-test, independent-samples Student T-test and Chi-Square test with a significance level of 5%. RESULTS: At all levels of both groups, dentine thickness before preparation was greater than after preparation (p < .05). No difference in the percentage of dentine reduction was observed between TradAC and ConsAC groups (p > .05), but a significantly greater reduction was observed to the distal aspect of the roots (p < .05). After root canal preparation, dentine thinner than 0.5 mm was observed mostly along the distal aspect of the root (10% to 15%) of the MB and ML canals, with no influence of the access cavity type on its incidence to either mesial (X2  = 1.66; p = .2) or distal (X2  = 0.40; p = .5) directions. In the TradAC group, dentine thickness in most slices was greater than 1.0 mm after preparation (n = 124) whilst, in the ConsAC, it ranged from 0.5 to 1.0 mm (n = 136). CONCLUSION: Traditional or conservative access cavity preparation in extracted mandibular molars did not influence the remaining dentine thickness in the coronal third of mesial canals enlarged with thermomechanically treated nickel-titanium reciprocating instruments.

Assuntos