RESUMO
High-throughput screening methodologies to estimate lipid content in oleaginous yeasts use Nile red fluorescence in a given solvent and optimized excitation/emission wavelengths. However, Nile red fluorescence stabilization has been poorly analyzed, and high variability occurs when relative fluorescence is measured immediately or a few minutes after dye addition. The aim of this work was to analyze the fluorescence of Nile red at different incubation times using a variety of solvents and oleaginous/non-oleaginous yeast strains. We showed that fluorescence stabilization occurs between 20 and 30 min, depending on the strain and solvent. Therefore, we suggest that fluorescence measurements should be followed until stabilization, where Relative Fluorescence Units should be considered after stabilization for lipid content estimation.
RESUMO
ABSTRACT Objective: The aim of this study is to analyze if both color and nylon fibers have an influence on microwave-cured acrylic resin properties. Methods: Rectangular and disk-shaped specimens were prepared using acrylic resins; medium pink with and without nylon fibers and colorless without nylon fibers. To obtain the rectangular specimens, a stainless steel die was used with the following dimensions: 64 X 10 x 3 mm (± 0.5mm). To obtain disk-shaped specimens, a die 50mm (±0.5mm) in diameter and 0.5mm (±0.05mm) thick was employed. They were randomized to form groups: control (colorless acrylic) and experimental (medium pink, with and without nylon fibers), with each group consisting of ten (10) specimens rectangular in shape and five (5) disk-shaped. They were analyzed in six (6) assays (izod impact strength, n=10; Knoop hardness, n=10; glass transition temperature, n=3; water sorption and solubility, n=5; degree of monomer/polymer conversion, n=1; flexural strength and flexural modulus, n=10). All variables were subjected to the analysis of variance test followed by Tukey's multiple comparison test, at a 5% level of significance. Results: The analysis of the monomer/polymer degree of conversion did not reveal any difference between the three groups of resins (medium pink, with and without nylon fibers and colorless resin); it was approximately 88%. The results did not show significant differences between the groups for each variable (p>0.05). Conclusion: The results showed that color and presence of nylon fibers in acrylic resins did not affect the properties analyzed in this study.
RESUMO Objetivo: Analisar se corantes e fibras de nylon influenciam nas propriedades de uma resina acrílica ativada por energia de micro-ondas. Métodos: Espécimes retangulares e em forma de disco foram confeccionados em resina acrílica rosa médio com e sem fibras de nylon e incolor sem fibras. Para obter os espécimes retangulares, foi utilizada uma matriz de aço inoxidável com as seguintes dimensões: 64 X 10 X 3 (± 0,5mm) e para obter os espécimes em forma de disco, foi utilizada uma matriz com 50mm (± 0,5mm) de diâmetro e 0,5mm (±0,05mm) de espessura. Os mesmos foram randomizados para formar os grupos controle (acrílico incolor sem fibras) e experimentais (rosa médio com e sem fibras), sendo cada grupo composto por dez (10) espécimes retangulares e cinco (5) em forma de disco. Foram os mesmos então submetidos a seis (6) ensaios (resistência ao impacto izod, n=10; dureza knoop, n=10; temperatura de transição vítrea, n=3; sorção e solubilidade, n=5; grau de conversão, n=1; resistência à flexão e módulo de flexão, n=10). Todas as variáveis foram submetidas à análise de variância seguida pelo teste de comparações múltiplas de Tukey, com nível de significância de 5%. Resultados: O grau de conversão foi de 88% para os 3 grupos de resinas e os resultados não mostraram diferença estatisticamente significativa entre os mesmos para cada variável (p>0,05). Conclusão: Os resultados mostraram que o corante e a presença de fibras de nylon em resina acrílica não afetaram as propriedades analisadas nesse estudo.
RESUMO
Biofilms provide an ideal environment for protecting the microbial cells from damage caused by humoral and cellular immune system components, promoting resistance, infections and increasing mortality and morbidity of patients in health facilities. In an attempt to provide an innovative solution for preventing contamination in hospital environments, this study evaluated nine structural complementary fluorescent benzimidazo[1,2-α]quinolines as bifunctional agents that both detect and have biocidal activity against yeast biofilms on stainless steel surfaces. The benzimidazoles' staining capability was determined by a fluorescence microscopy study and spraying the substance on yeast biofilm contaminated stainless steel surfaces. Furthermore, their in vitro human leukocyte cytotoxicity was evaluated with trypan blue and their biocidal activity was determined as the minimum inhibitory concentration against Candida tropicalis, C. albicans and C. parapsilosis strains. Moreover, scanning electron micrographs were recorded to study the biocidal activity. This resulted in the identification of 7, which presents all the desired characteristics (such as solubility) and capabilities (staining and biocide activity against all tested biofilm forming yeast strains) at the same time. As such, benzimidazole 7 has the potential to guarantee the use of disinfected medical and surgical instruments in clinical and surgical procedures, consequently, contributing to an increased safety for patients.
Assuntos
Biofilmes , Candida albicans/efeitos dos fármacos , Candida albicans/fisiologia , Corantes Fluorescentes/química , Corantes Fluorescentes/farmacologia , Quinolinas/química , Quinolinas/farmacologia , Antifúngicos/química , Antifúngicos/farmacologia , Biofilmes/efeitos dos fármacos , Candida albicans/isolamento & purificação , Farmacorresistência Fúngica/efeitos dos fármacos , Testes de Sensibilidade MicrobianaRESUMO
Three novel fluorescent dyes were evaluated for the detection of latent fingermarks on different types and colors of adhesive tapes. Compared with the conventional reagents used to reveal latent fingermarks on these surfaces, these new fluorescent dyes have many advantages. They are highly selective to fingermarks, require only a simple procedure, do not need pre- or post-treatment, have high thermal and photochemical stability, are low in cost and use only water as a solvent. In addition, the emitted fluorescence creates a sharp contrast with the fingermark surface, meaning the fingermarks can be clearly visualized and photographed when excited with longwave ultraviolet light (365nm).
Assuntos
Adesivos , Dermatoglifia , Corantes Fluorescentes , Humanos , Análise Espectral , Raios UltravioletaRESUMO
Objective: The objective of this study was to evaluate the effectiveness of disinfection methods in microwave and immersion in peracetic acid in heat-cured, self-cured and microwave-cured acrylic resin, contaminated with Candida albicans.Methods: Five specimens were prepared for each type of acrylic resin. All were infected with Candida Albicans, incubated at 37°C for 24 hours. The group which underwent microwave energy was irradiated with a power of 840W for 1 minute and the other group underwent disinfection by soaking of 0.2% peracetic acid for 5 minutes.Results: All samples proved to be contaminated after the incubation period. After the different processes of disinfection, both immersion in 0.2% peracetic acid as microwave irradiation were effective in disinfection of the 3 types of acrylic resins contaminated by Candida Albicans.Conclusion: Concluded that soaking in 0,2% peracetic acid for 5 minutes with microwave irradiation power 840W for 1 minute are effective methods for disinfecting heat-cured acrylic resin, self-cured acrylic resin and microwave-cured acrylic resin, contaminated with Candida Albicans.
Objetivo: Avaliar a eficácia dos métodos de desinfecção em microondas e imersão em ácido peracético em resina acrílica termopolimerizável, autopolimerizável e resina acrílica polimerizada por microondas, contaminadas com Candida albicans.Métodos: Cinco amostras foram preparadas para cada tipo de resina acrílica. Todas foram infectadas com Candida Albicans, incubadas a 37 ° C durante 24 h. O grupo submetido a energia de microondas foi irradiada com uma potência de 840W durante 1 minuto e o outro grupo foi submetido a desinfecção por imersão de ácido peracético a 0,2% durante 5 minutos.Resultados: Todas as amostras mostraram estar contaminadas depois do período de incubação. Depois dos diferentes processos de desinfecção, tanto a imersão em 0,2% de ácido peracético, como a irradiação de microondas foram eficazes na desinfecção dos 3 tipos de resinas acrílicas contaminados por Candida Albicans.Conclusão: Concluiu-se que a imersão em ácido peracético 0,2% durante 5 minutos e a irradiação de microondas com potência de 840W durante 1 minuto são métodos eficazes para a desinfecção de resina acrílica termopolimerizável, resina acrílica autopolimerizável e resina acrílica polimerizada por microondas, contaminados com Candida Albicans.
RESUMO
INTRODUCTION: Sporothrix schenckii is a thermal dimorphic pathogenic fungus causing a subcutaneous mycosis, sporotrichosis. Nitrocoumarin represents a fluorogenic substrate class where the microbial nitroreductase activity produces several derivatives, already used in several other enzyme assays. The objective of this study was the analysis of 6-nitrocoumarin (6-NC) as a substrate to study the nitroreductase activity in Sporothrix schenckii. METHODS: Thirty-five samples of S. schenckii were cultivated for seven, 14 and 21 days at 35 °C in a microculture containing 6-nitrocoumarin or 6-aminocoumarin (6-AC) dissolved in dimethyl sulfoxide or dimethyl sulfoxide as a negative control, for posterior examination under an epifluorescence microscope. The organic layer of the seven, 14 and 21-day cultures was analyzed by means of direct illumination with 365 nm UV light and by means of elution on G silica gel plate with hexane:ethyl acetate 1:4 unveiled with UV light. RESULTS: All of the strains showed the presence of 6-AC (yellow fluorescence) and 6-hydroxylaminocoumarin (blue fluorescence) in thin layer chromatography, which explains the green fluorescence observed in the fungus structure. CONCLUSION: The nitroreductase activity is widely distributed in the S. schenckii complex and 6-NC is a fluorogenic substrate of easy access and applicability for the nitroreductase activity detection.
Assuntos
Cumarínicos/metabolismo , Corantes Fluorescentes/metabolismo , Nitrorredutases/metabolismo , Sporothrix/enzimologia , Cromatografia em Camada Fina , Especificidade por Substrato , Raios UltravioletaRESUMO
Introduction Sporothrix schenckii is a thermal dimorphic pathogenic fungus causing a subcutaneous mycosis, sporotrichosis. Nitrocoumarin represents a fluorogenic substrate class where the microbial nitroreductase activity produces several derivatives, already used in several other enzyme assays. The objective of this study was the analysis of 6-nitrocoumarin (6-NC) as a substrate to study the nitroreductase activity in Sporothrix schenckii. Methods Thirty-five samples of S. schenckii were cultivated for seven, 14 and 21 days at 35 °C in a microculture containing 6-nitrocoumarin or 6-aminocoumarin (6-AC) dissolved in dimethyl sulfoxide or dimethyl sulfoxide as a negative control, for posterior examination under an epifluorescence microscope. The organic layer of the seven, 14 and 21-day cultures was analyzed by means of direct illumination with 365 nm UV light and by means of elution on G silica gel plate with hexane:ethyl acetate 1:4 unveiled with UV light. Results All of the strains showed the presence of 6-AC (yellow fluorescence) and 6-hydroxylaminocoumarin (blue fluorescence) in thin layer chromatography, which explains the green fluorescence observed in the fungus structure. Conclusion The nitroreductase activity is widely distributed in the S. schenckii complex and 6-NC is a fluorogenic substrate of easy access and applicability for the nitroreductase activity detection. .
Introdução Sporothrix schenckii é um fungo dimórfico térmico, agente etiológico de micose subcutânea, a esporotricose. Nitrocumarina representa classe de substratos fluorogênicos em que a atividade nitroredutásica microbiana produz vários derivados, já utilizados em vários outros ensaios enzimáticos. O objetivo deste estudo foi analisar 6-nitrocumarina (6-NC) como substrato para estudo da atividade nitroredutásica em Sporothrix schenckii. Métodos Trinta e cinco isolados de S. schenckii foram cultivados por sete, 14 e 21 dias a 35 °C em um microcultivo contendo 6-nitrocumarina ou 6-aminocumarina (6-AC) solubilizada em dimetilsulfóxido ou dimetilsulfóxido como controle negativo, para posterior análise em microscópio de epifluorescência. A fase orgânica da cultura de sete, 14 e 21 dias foi analisada por meio de iluminação direta com luz UV de 365 nm e por eluição em placas de sílica gel G com hexano:acetato de etila 1:4 e revelada com luz UV. Resultados Todos os isolados mostraram a presença de 6-AC (fluorescência amarela) e 6-hidroxilaminocumarina (fluorescência azul) em cromatografia em camada delgada, que explica a fluorescência verde observada na estrutura dos fungos. Conclusão A atividade nitroredutásica é amplamente distribuída no complexo S. schenckii e 6-NC é um substrato fluorogênico de fácil obtenção e aplicabilidade para detecção da atividade nitroredutásica. .
Assuntos
Cumarínicos/metabolismo , Corantes Fluorescentes/metabolismo , Nitrorredutases/metabolismo , Sporothrix/enzimologia , Cromatografia em Camada Fina , Especificidade por Substrato , Raios UltravioletaRESUMO
Este trabalho avalia o uso de corante fluorescente do grupo dos compostos heterocíclicos benzazólicos em protocolo diagnóstico para oocistos de Cryptosporidium spp. em lâminas de esfregaços fecais. De um total de 578 amostras fecais foram selecionadas 54 (9,34%) positivas para oocistos de Cryptosporidium spp., evidenciadas pela técnica de Ziehl-Neelsen modificada (ZNm) e testadas com o corante fluorescente 2-(2-hidroxi-5aminofenil) benzoxazol isotiocianato(BzICT). A leitura das lâminas observadas em microscopia de epifluorescência confirmou todas as amostras positivas por ZNm. O corante fluorescente mostrou fotoestabilidade nas lâminas de esfregaços fecais. Este corante está ainda sendo investigado sob outras condições, tais como amostras fecais frescas, diferentes tempos de impregnação do fluorocromo, trocas nos valoresde pH e esforço para reduzir o background de outros componentes das amostras fecais, como restos de material celulósico.
RESUMO
Este trabalho avalia o uso de corante fluorescente do grupo dos compostos heterocíclicos benzazólicos em protocolo diagnóstico para oocistos de Cryptosporidium spp. em lâminas de esfregaços fecais. De um total de 578 amostras fecais foram selecionadas 54 (9,34%) positivas para oocistos de Cryptosporidium spp., evidenciadas pela técnica de Ziehl-Neelsen modificada (ZNm) e testadas com o corante fluorescente 2-(2-hidroxi-5aminofenil) benzoxazol isotiocianato(BzICT). A leitura das lâminas observadas em microscopia de epifluorescência confirmou todas as amostras positivas por ZNm. O corante fluorescente mostrou fotoestabilidade nas lâminas de esfregaços fecais. Este corante está ainda sendo investigado sob outras condições, tais como amostras fecais frescas, diferentes tempos de impregnação do fluorocromo, trocas nos valoresde pH e esforço para reduzir o background de outros componentes das amostras fecais, como restos de material celulósico.
RESUMO
Two Schiff bases were synthesized by reaction of 2-(4'-aminophenyl)benzoxazole derivatives with 4-N,N-diethylaminobenzaldehyde. UV-visible (UV-vis) and steady-state fluorescence in solution were applied in order to characterize its photophysical behavior. The Schiff bases present absorption in the UV region with fluorescence emission in the blue-green region, with a large Stokes' shift. The UV-vis data indicates that each dye behaves as two different chromophores in solution in the ground state. The fluorescence emission spectra of the dye 5a show that an intramolecular proton transfer (ESIPT) mechanism takes place in the excited state, whereas a twisted internal charge transfer (TICT) state is observed for the dye 5b. Theoretical calculations were performed in order to study the conformation and polarity of the molecules at their ground and excited electronic states. Using density functional theory (DFT) methods at theoretical levels BLYP/Aug-SV(P) for geometry optimizations and B3LYP/6-311++G(2d,p) for single-point energy evaluations, the calculations indicate that the lowest energy conformations are in all cases nonplanar and that the dipole moments of the excited state relaxed structures are much larger than those of the ground state structures, which corroborates the experimental UV-vis absorption results.