RESUMO
This study investigated the effect of CO2 laser irradiation on the inhibition of secondary caries on root surfaces adjacent to glass ionomer cement (GIC) or composite resin (CR) restorations. 40 dental blocks were divided into 4 groups: G1 (negative control): cavity preparation + adhesive restoration with CR; G2: (positive control) cavity preparation + GIC restoration; G3: equal to group 1 + CO2 laser with 6 J/cm(2); G4: equal to group 2 + CO2 laser. The blocks were submitted to thermal and pH cycling. Dental demineralization around restorations was quantified using microhardness analyses and Light-Induced Fluorescence (QLF). The groups showed no significant differences in mineral loss at depths between 20 µm and 40 µm. At 60 µm, G2 and G3 ≠ G1, but G4 = G1, G2 and G3. At 80 µm, G4 ≠ G1, and at 100 µm, G4 = G2 = G1. At 140 and 220 µm, G2, G3, and G4 = G1. The averages obtained using QFL in groups 1, 2, 3, and 4 were 0.637, 0.162, 0.095, and 0.048, respectively. QLF and microhardness analyses showed that CO2 laser irradiation reduced mineral loss around the CR restorations but that it did not increase the anticariogenic effect of GIC restorations.
Assuntos
Resinas Compostas , Cárie Dentária/cirurgia , Reparação de Restauração Dentária , Cimentos de Ionômeros de Vidro , Lasers de Gás , Humanos , Resultado do TratamentoRESUMO
OBJECTIVES: The aim of this in vitro study was to evaluate the microleakage in occlusal surfaces, after preparation with Er:YAG laser and compared to the diamond-bur conventional technique. METHODS: Thirty premolars were divided into three groups: I - high-speed handpiece + 37% phosphoric acid; II - Er:YAG laser (350 mJ, 4 Hz and 112 J/cm(2)) + 37% phosphoric acid; and III - Er:YAG laser (350 mJ, 4 Hz and 112 J/cm(2)) + Er:YAG laser (80 mJ, 4 Hz, and 25 mJ/cm(2)). All cavities received the same adhesive system and were restored with flowable composite according to manufacturer's instructions. Teeth were submitted to thermal cycling and immersed in 50% silver nitrate solutions for 8 h in total darkness. Specimens were sectioned longitudinally in the bucco-lingual direction, in slices of 1 mm thick. Each slice was immersed into photo developing solution and was photographed, and microleakage was scored from 0 to 7, by three calibrated examiners. RESULTS: A statistically significant difference (P < 0.0001) was observed between Er:YAG laser prepared and etched specimens and those in the other groups. CONCLUSIONS: It can be concluded that no significant difference was noted between the two types of enamel preparation when etching was performed. Preparing and treating the enamel surface exclusively by Er:YAG laser resulted in the highest degree of leakage.
Assuntos
Infiltração Dentária , Terapia a Laser , Preparo do Dente/métodos , Resinas Acrílicas/química , Distribuição de Qui-Quadrado , Resinas Compostas/química , Humanos , Selantes de Fossas e Fissuras/química , Poliuretanos/química , Estatísticas não Paramétricas , Preparo do Dente/instrumentaçãoRESUMO
This study analyzed in vitro two brands of one-step adhesive systems of fourth generation (Optisolo--Kerr, filled; and Single Bond--3M, unfilled) and two composite resins (Prodigy--Kerr and Z100--3M), aiming at evaluating their bond strength to dentin. Eighty human extracted molars were embedded in acrylic resin and grounded until dentin was exposed in longitudinal direction. The specimens were divided in 4 groups. Composite resin cones were bonded to the specimens using the mentioned adhesive systems, following the instructions of the manufacturers. The test-specimens were submitted to tensile tests using a 4442 Universal Mini-Instron Machine with the speed of 0.5 mm/min. The results were converted into MPa, according to the area of adhesion, and submitted to statistical analysis with ANOVA. There was significant statistical difference (p < 0.01) between the adhesive systems (F = 7.24). Optisolo (m = 11.03 +/- 4.23) showed better bond strength than Single Bond (m = 8.37 +/- 4.54). There was no significant statistical difference (p > 0.05) between the composites (F = 0.43).
Assuntos
Bis-Fenol A-Glicidil Metacrilato , Resinas Compostas , Colagem Dentária , Adesivos Dentinários , Metacrilatos , Humanos , Técnicas In VitroRESUMO
OBJECTIVE: This study evaluated microleakage of composite restorations submitted to marginal treatment with Nd:YAG laser and surface sealant. BACKGROUND DATA: Previous studies have demonstrated that Nd:YAG-lased enamel melted and became recrystallized with a morphologic appearance similar to lava, and has been used clinically in the sealing of enamel pits and fissures. METHODS: Class V cavities in enamel of human premolars were restored with composite resin (Z100, 3M) and randomly divided in six groups: G1, control; G2, surface sealant marginal treatment; G3 to G6, were treated with pulsed Nd:YAG laser (1.064 microm) marginal treatment, contact fiberoptic (300 microm), air cooling, for 30 seconds, powers of 1.2-2 W, repetition rates of 20-30 Hz, energies of 40-100 mJ. Teeth were impermeabilized, immersed in a rhodamine dye, sectioned, and evaluated under stereomicroscope microscopy with scores. RESULTS: There were significant differences between marginal treatments; there were no differences between groups 1, 2, and 4, and 3,5, and 6; lower values of microleakage were at groups 3, 5, and 6 (Kruskal-Wallis,p = 0.05). CONCLUSION: Nd:YAG laser showed improved marginal sealing and decreased microleakage of composite resins restorations.