RESUMO

This study sought to assess the effect of different surface finishing and polishing protocols on the surface roughness and bacterial adhesion (S. sanguinis) to polymethyl methacrylates (PMMA). Fifty specimens were divided into 5 groups (n = 10) according to their fabrication method and surface finishing protocol: LP (3 : 1 ratio and laboratory polishing), NF (Nealon technique and finishing), NP (Nealon technique and manual polishing), MF (3 : 1 ratio and manual finishing), and MP (3 : 1 ratio and manual polishing). For each group, five specimens were submitted to bacterial adhesion tests and analyzed by scanning electron microscopy (SEM). Two additional specimens were subjected to surface topography analysis by SEM and the remaining three specimens were subjected to surface roughness measurements. Data were compared by one-way ANOVA. The mean bacterial counts were as follows: NF, 19.6 ± 3.05; MP, 5.36 ± 2.08; NP, 4.96 ± 1.93; MF, 7.36 ± 2.45; and LP, 1.56 ± 0.62 (CFU). The mean surface roughness values were as follows: NF, 3.23 ± 0.15; MP, 0.52 ± 0.05; NP, 0.60 ± 0.08; MF, 2.69 ± 0.12; and LP, 0.07 ± 0.02 (µm). A reduction in the surface roughness was observed to be directly related to a decrease in bacterial adhesion. It was verified that the laboratory processing of PMMA might decrease the surface roughness and consequently the adhesion of S. sanguinis to this material.

RESUMO

The current study evaluated prosthetic dental crowns obtained by optical scanning and a computer-aided designing/computer-aided manufacturing system using micro-computed tomography to compare the marginal fit. The virtual models were obtained with four different scanning surfaces: typodont (T), regular impressions (RI), master casts (MC), and powdered master casts (PMC). Five virtual models were obtained for each group. For each model, a crown was designed on the software and milled from feldspathic ceramic blocks. Micro-CT images were obtained for marginal gap measurements and the data were statistically analyzed by one-way analysis of variance followed by Tukey's test. The mean vertical misfit was T = 62.6 ± 65.2 µm ; MC = 60.4 ± 38.4 µm; PMC = 58.1 ± 38.0 µm, and RI = 89.8 ± 62.8 µm. Considering a percentage of vertical marginal gap of up to 75 µm, the results were T = 71.5%, RI = 49.2%, MC = 69.6%, and PMC = 71.2%. The percentages of horizontal overextension were T = 8.5%, RI = 0%, MC = 0.8%, and PMC = 3.8%. Based on the results, virtual model acquisition by scanning the typodont (simulated mouth) or MC, with or without powder, showed acceptable values for the marginal gap. The higher result of marginal gap of the RI group suggests that it is preferable to scan this directly from the mouth or from MC.

Assuntos

RESUMO

In the past, the Branemark Novum protocol for the immediate functional loading of a mandibular fixed implant supported prosthesis provided an effective alternative for select patients. However, the manufacturer has discontinued this design, and only a few selected prosthetic-related replacement components are currently available. This clinical report presents the loss of an implant associated with a discontinued system. To take advantage of all of the preexisting components, it proposes a rescue procedure that allows continuous use of the original fixed restoration during the restoration of the tripod support at the implant level.

Assuntos

RESUMO

PURPOSE: This study sought to evaluate the influence of methodologic aspects on variations in the findings of in vitro microleakage studies of the implant-abutment interface. MATERIALS AND METHODS: The MEDLINE, EMBASE, and Cochrane Library databases were consulted for in vitro studies published between 1990 and August 2011. Date from the studies that met the inclusion and exclusion criteria were arranged in tables and subjected to descriptive analysis. RESULTS: Twenty-one studies were found to be eligible for the analysis after application of the inclusion/exclusion criteria. Sixteen studies used bacteria (76.2%), one used a bacterial toxin (4.76%), one used saliva (4.76%), two employed dyes (9.52%), and one used a combination of dyes and bacteria (4.76%). Eight studies evaluated microleakage from the inner portion of the implant to the external portion (38.1%) and nine examined the reverse (42.85%), while four studies investigated the relationship between them (19.05%). The volume inoculated inside the implants ranged from 0.1 to 5.0 mL. The bacterial concentrations used in the tests ranged from 2.41 x 106 to 8 x 108 colony-forming units/mL. Oral bacterial flora; mixtures of bacteria, toluidine blue, and gentian violet; and lipopolysaccharide of Salmonella enterica bacterial toxins were used. The monitoring period of test results ranged from 24 hours to 11 weeks for bacteria, 5 minutes to 7 days for dye, and 7 days for bacterial toxins. In four studies, microleakage was correlated with the size of the implant-abutment microgap. The external-hexagon implant configuration showed the greatest microleakage, followed by internal-trilobe, internal-hexagon, and internal-taper configurations. CONCLUSION: The lack of standardization hinderd comparisons of the studies and could explain the divergent results. It is suggested for future studies that special emphasis be placed upon inoculation and analysis of the specific volume for each system, lower concentrations of inoculated bacterial suspensions, and shorter follow-up time when using bacteria.

Assuntos

RESUMO

PURPOSE: The aim of this retrospective study was to evaluate the long-term survival rates and the frequency of complications associated with single implants and their associated restorations. MATERIALS AND METHODS: A retrospective cohort study was performed in patients who received dental implants between 1997 and 2007. The cohort included patients who had a single implant restored with a cemented or screwed restoration that had been in function for more than 2 years. The cumulative implant survival rates and peri-implant conditions (marginal bone loss, pocket depth, and plaque, gingival, and bleeding indices), as well as prosthodontic maintenance requirements, were evaluated. Descriptive statistics, the chi-square test, and regression models were used. RESULTS: Seventy-three implants were placed in 44 patients (32 women, 12 men; mean age, 48 years). All implants were available for follow-up after 2 to 13 years (mean follow-up, 60 months). The overall cumulative 5-year survival rates for implants were 95.9%, and most of the prostheses (98.6%) remained functional throughout the observation period. The overall frequency of complications was 29.6% (4.3% inflammatory, 22.5% prosthetic, 2.8% operative). The average peri-implant marginal bone loss was 1.8 mm. Peri-implant soft tissue conditions such as plaque and bleeding indices and pocket depths were also satisfactory. However, the presence of inflammation was significantly associated with pocket depth and gingival keratinized mucosa. The need to retighten loose abutment screws (21%) was the most frequent prosthodontic maintenance performed. However, all loose abutment screws occurred in prostheses retained with titanium screws, and 92.9% of the prostheses had a UCLA-type abutment. CONCLUSION: The implants and the associated prosthetic constructions used in this study showed excellent survival rates. However, there was a high frequency of prosthetic complications associated with titanium screws and UCLA cast abutments. Other prosthetic components may have yielded different results.

Assuntos

RESUMO

The purpose of this study was to warn the dental community about a possible problem in function with partial implant-supported prostheses used for long periods. The misalignment between natural teeth and the implant-supported prosthesis on teeth 11 and 12, observed in a 14-year clinical follow-up, illustrates the fact. The metal-ceramic crowns were placed in 1995 after a rigorous occlusal adjustment. Evaluations were made at 4, 6, 9, and 14 years, when it was noticed that the restorations were positioned palatally and extruded in comparison with the natural teeth. After 9 years, a greater discrepancy was noticed, with anterior occlusion and esthetic changes. The possible causes have been discussed: occlusal problems, parafunctional habits, and natural movement. The first 2 options were discarded after clinical analysis and diagnosis. Therefore, the natural movement probably deriving from an interaction of mechanical and genetic factors might have been the cause. The implants do not have periodontal ligaments but rather ankylosis, so they do not suffer those movements. This case emphasizes the need to inform patients that implants can last more than 10 years in function, but this is not the case with restorations, which lose function and esthetics and must be replaced.

Assuntos

RESUMO

PURPOSE: The aim of this study was to verify quality of life related to oral health and satisfaction with dentures. Conventional mandibular complete dentures were converted to overdentures retained by two implants with immediate loading (bar-clip system, n = 16). MATERIALS AND METHODS: The Brazilian short version of the Oral Health Impact Profile (OHIP-14Br) was used to evaluate the impact of oral health on quality of life. Satisfaction with the prostheses was obtained by means of a questionnaire addressing satisfaction with the present prostheses and through use of a visual analog scale (VAS). RESULTS: The results of the OHIP-14Br questionnaire were verified at 3 and 6 months after conversion from complete dentures to a mandibular overdenture. The satisfaction questionnaire for the mandibular prostheses obtained 43.75% satisfaction before conversion and 100% satisfaction at 1 week and 3 and 6 months after conversion. The satisfaction results of the prostheses, both maxillary and mandibular, were 68.75% before conversion, 93.75% at 1 week and 3 months after conversion, and 87.5% at 6 months. There was an immediate improvement in patients' satisfaction with the mandibular overdenture prostheses regarding stability and retention (Friedman test, P = .000) and quality of life (Friedman test, P = .001). CONCLUSION: The improvement seen justifies the immediate loading approach used in this study.

Assuntos

RESUMO

Lower conventional complete dentures were converted to overdentures retained by two implants with an immediately loaded bar-clip system (n 16). The masticatory performance test was carried out using 'Optocal' after forty chewing strokes. Nutritional condition was evaluated by means of a Mini-Nutritional-Assessment questionnaire. No individual was classified as malnourished. The masticatory performance test demonstrated a statistically significant difference before conversion (baseline) and 3 and 6 months after conversion of the lower conventional complete denture to an implant-retained overdenture (paired-samples t test; P < 0·05). A statistically significant difference before and after 6 months of conversion for nutritional condition (Wilcoxon test; P < 0·05) was also observed. The association between masticatory performance and nutritional assessment demonstrated that a statistically significant difference between masticatory performance of the subgroups classified at baseline as nourished (22·43 %) and those at risk of malnutrition (3·9 %) was only evidenced before conversion (P = 0·006). After the conversion from a lower conventional complete denture to an implant-retained overdenture, at 3 months, the risk of malnutrition and nourished at baseline did not present significant differences in masticatory performance. Nonetheless, the mean masticatory performance potential was 19·86 and 31·98 % for subgroups classified at baseline as at risk of malnutrition and nourished, respectively (P = 0·187). The results before conversion were less favourable for masticatory performance and nutritional condition. The increased retention of the mandibular prosthesis allowed improvement in masticatory performance and nutritional condition.

Assuntos

RESUMO

This study compared vertical and passive fit of one-piece cast frameworks made with 3 different materials: commercially pure titanium (CP Ti - G1), cobalt-chromium alloy (Co-Cr - G2) and nickel-chromium-titanium alloy (Ni-Cr-Ti - G3). Fifteen frameworks were obtained simulating bars for fixed prosthesis in a model with 5 implants. The passive and vertical fit of the framework interface was measured using an optical microscope at x30 magnification. Data were statistically analyzed by ANOVA and LSD tests (α=0.05). Mean and standard deviation values for passive fit and vertical fit were, respectively: G1 [472.49 (109.88) µm and 29.9 (13.24) µm], G2 [584.84 (120.20) µm and 27.05 (10.30) µm], and G3 [462.70 (179.18) µm and 24.95 (11.14) µm]. For vertical fit, there were no significant differences among G1, G2 and G3 (p=0.285). There were no significant differences for passive fit between G1 and G3 (p=0.844), but both differed significantly from G2 (p=0.028 and p=0.035, respectively), which showed the highest misfit values. It may be concluded that the vertical fit of frameworks was not affected by the tested materials, and that one-piece cast frameworks resulted in inadequate passive fit. The Co-Cr alloy presented the worst values for passive fit.

Assuntos

RESUMO

PURPOSE: To investigate the peri-implant stress fields generated from four different implant-abutment interfaces under axial loading applied at the center of the implant and several millimeters away from the implant center via photoelastic analysis. MATERIALS AND METHODS: Similar unthreaded and cylindric implants and abutments were fabricated and embedded in photoelastic resin with four different implant-abutment interfaces: external hex, internal hex, internal taper (11.5 degrees), and solid connection to the abutment (one piece). The samples were submitted to vertical compressive loads; one was applied at the implant center (1.5 kg; centered load), and the other was applied 6.5 mm away from the center, 4.4 mm from the outside of the outer aspect of the implant (0.75 kg; off-centered load). The maximum shear stresses were determined and observed at 46 points around the implants under the centered load and at 61 points under the off-center load in the photoelastic models. Graphics describing the maximum shear stress (y-axis) and the analyzed points (x-axis) were obtained, and areas under the curves were calculated. RESULTS: The centered loading (all points) resulted in small differences. The lowest amounts of stress were observed for the internal-taper implants, and values were minimally greater (0.4% to 3.3%) for the other implants. No statistically significant differences were found between groups for the centered load in any area. Under an off-center load, the internal-hex implants presented the least stress (all points). For off-center loading, the internal-hexagon implants differed significantly from the external-hex and one-piece implants and displayed the lowest stress levels. CONCLUSION: Under an off-center load, the internal-hex interfaces presented the lowest stress concentrations, internal-taper interfaces presented intermediate results, and one-piece and external-hex implants resulted in high stress levels. Centralized axial loads produced similar results.

Assuntos