RESUMO

The aim of this study was to verify the effectiveness of attenuated total reflectance-fourier transform infrared (ATR-FTIR) spectroscopy in the characterization of bone repair in mandibular osteotomy using erbium, chromium-doped yttrium, scandium, gallium and garnet (Er,Cr:YSGG) laser and multilaminate drill on each side. Two mandible bone fragments were removed from 30 rabbits, and the process of bone repair was studied immediately, 3, 7, 15, 21, and 28 days after the surgery. The histological analysis allowed detecting differences in the early stages of tissue repair after bone cutting performed with the Er,Cr:YSGG laser or multilaminate drill. The ATR-FTIR spectroscopy technique was sensitive to changes in the organic content of bone tissue repair process.

RESUMO

Abstract Oral soft tissue lesions require a precise diagnosis by oral biopsy with the ability to recognize these lesions within histopathological levels, so the instrument used for the incisions should be safe and cause little to no harm to the surrounding tissue. Objective This study compared a dual-wavelength diode laser and an Er, Cr:YSGG laser in oral soft tissue incisions to determine the most effective and safest laser system at the histopathological level. Methodology The (810 and 980 nm) dual-wavelength diode laser was used at 1.5 W and 2.5 W (CW) power settings, and the (2780 nm) Er, Cr:YSGG laser was used at 2.5 W and 3.5 W (PW) power settings. Both laser systems were used to incise the tissues of freshly dissected sheep tongue pieces to obtain the following histopathological criteria: epithelial tissue changes, connective tissue changes, and lateral thermal damage extent by optical microscopy. Results The epithelial and connective tissue damage scores were significantly higher in the dual-wavelength diode laser groups than in the Er, Cr:YSGG laser groups (P<0.001), and there was a significant difference between some groups. The extent of lateral thermal damage was also significantly higher in the diode laser groups than in the Er, Cr: YSGG laser groups (P<0.001), and there was a significant difference between groups. Group 2 (2.5 W) of the diode laser was the highest for all three criteria, while group 3 (2.5 W) of the Er, Cr:YSGG laser was the lowest. Conclusion The Er, Cr:YSGG laser with an output power of 2.5 W is, histologically, the most effective and safest laser for oral soft tissue incision. The dual-wavelength diode laser causes more damage than the Er, Cr:YSGG laser, but it can be used with a low output power and 1 mm safety distance in excisional biopsy.

RESUMO

The internal topography of the root canal is complex, especially for the permanent molar's mesial root. In response to such issues, improved irrigation techniques have been created, which use laser pulses to agitate fluids and improve microbial deposit removal. Objective: To assess the effectiveness of the Er,Cr:YSGG laser with a wavelength of 2,780 nm via photon-induced photoacoustic streaming (PIPS) protocol which agitated of 2% chlorohexidine (CHX) in removing mature Enterococcus faecalis (E. faecalis) biofilm in root canal systems of lower molars. Material and Methods: The mesial roots of lower first and second molars were separated and inoculated with E. faecalis bacterial suspension for 30 days. The roots were irrigated with CHX, some of them were agitated with a passive ultrasonic device (PUI), while the other roots were agitated by an Er,Cr:YSGG laser in PIPS at 60 µs/pulse, 5 Hz, (0.25, 0.5, 0.75, and 1) W. An atomic force microscope (AFM) was used as a new method to get the results in the isthmus area; the obtained results from each group were compared with each other. Results: Based on the AFM and SEM analyses, laser and ultrasonic activation groups showed higher antimicrobial efficacy than the conventional syringe irrigation group (P<0.05). Conclusion: Based on the investigation's findings, the activation of 2% CHX solution by Er,Cr:YSGG laser in PIPS and PUI offers better mature bacterial biofilm removal in the mesial root of lower human molars than the same irrigant with the SI technique (AU)

A topografia interna do canal radicular é complexa, especialmente para a raiz mesial do molar permanente. Em resposta a esses problemas, foram criadas técnicas aprimoradas de irrigação, que utilizam pulsos de laser para agitar fluidos e melhorar a remoção de depósitos microbianos. Objetivo: Avaliar a eficácia do laser Er,Cr:YSGG com comprimento de onda de 2.780 nm via protocolo de streaming fotoacústico induzido por fótons (PIPS) que agitou clorohexidina a 2% (CHX) na remoção de Enterococcus faecalis maduro (E. faecalis) biofilme em sistemas de canais radiculares de molares inferiores. Material e Métodos: As raízes mesiais de 28 primeiros e segundos molares inferiores foram separadas e inoculadas com suspensão bacteriana de E. faecalis por 30 dias. As raízes foram irrigadas com CHX, sendo algumas delas agitadas com aparelho ultrassônico passivo (PUI), enquanto as demais raízes foram agitadas com laser Er,Cr:YSGG em PIPS a 60 µs/pulso, 5 Hz (0,25, 0,5, 0,75 e 1) W. Um microscópio de força atômica (AFM) foi utilizado como um novo método para obter os resultados na área do istmo; os resultados obtidos de cada grupo foram comparados entre si. Resultados: Com base nas análises de AFM e SEM, os grupos de ativação por laser e ultrassom apresentaram maior eficácia antimicrobiana do que o grupo de irrigação com seringa convencional (P<0.05). Conclusão: Com base nos achados da investigação, a ativação da solução de CHX a 2% pelo laser Er,Cr:YSGG em PIPS a (60 µs/pulso, 5 Hz, 0,75 W) oferece melhor remoção de biofilme (AU)

Assuntos

RESUMO

Background: The debonding of crowns and ceramic veneers with laser is already a reality in the clinic. It presents benefits in comparison to traditional removal with the use of a rotating instrument; however, there is still no consolidated protocol and many professionals use it without the necessary scientific basis. Objective: The aim of this work was to perform a literature review on the debonding of indirect ceramic restorations using the Er:YAG and Er,Cr:YSGG lasers to provide clinical professionals and the scientific community a careful analysis, and also to guiding the use of irradiation at laser for such procedures. Methods: Bibliographic searches were performed in the following databases: Pubmed, Web of Science and Google Scholar. According to the inclusion criteria adopted, twenty-seven clinical and in vitro studies were selected in the period from 2007 to 2021. In the present work, the composition of the crowns and facets, as well as the types of cement and the laser irradiation protocols adopted in the selected studies is detailed. Conclusions: It was concluded that the use of erbium lasers for debonding of indirect ceramic restorations proved to be more selective and conservative when compared to removal with a rotary diamond instrument. Furthermore, it was shown to be in more efficient in debonding different types of ceramics. However, there are great variations in the "debonding" protocols, which emphasizes the need for further studies that seek to standardize the irradiation protocols considering the different clinical situations (AU)

Antecedentes: A remoção de coroas e facetas cerâmicas com laser já é uma realidade clínica e apresenta benefícios em relação à remoção tradicional com uso de instrumento rotatório diamantado; entretanto, ainda não existe um protocolo consolidado e muitos profissionais o utilizam sem o embasamento científico necessário. Objetivos: O objetivo deste trabalho foi realizar uma revisão da literatura sobre a remoção de restaurações cerâmicas indiretas utilizando os lasers Er:YAG e Er,Cr:YSGG para fornecer uma análise cuidadosa aos profissionais clínicos e à comunidade científica, além de orientar o uso da irradiação a laser para tal aplicação. Métodos: As buscas bibliográficas foram realizadas, nas seguintes bases de dados: Pubmed, Web of Science e Google Scholar. De acordo com os critérios de inclusão adotados, foram selecionados vinte e sete estudos clínicos e in vitro no período de 2007 a 2021. No presente trabalho, a composição das coroas e facetas, bem como os tipos de cimento e os protocolos de irradiação laser adotados nos estudos selecionados foram detalhados. Conclusão: Concluiu-se que o uso dos lasers de érbio para remoção de restaurações cerâmicas indiretas mostrou-se mais seletivo e conservador quando comparado à remoção com instrumento rotatório diamantado, além de ser eficiente na remoção de diferentes tipos de cerâmicas. No entanto, existem grandes variações nos protocolos de "debonding", o que enfatiza a necessidade de novos estudos que busquem uma padronização dos protocolos de irradiação considerando as diferentes situações clínicas.(AU)

Assuntos

RESUMO

Laminate veneer removal is becoming a routine procedure at the dental clinic and the use of laser can facilitate its removal. This work aimed to evaluate the morphological, elemental, and optical changes in the remaining enamel after veneer removal using Er,Cr:YSGG laser. Forty-four enamel slabs were prepared and randomly distributed into nine experimental groups, for bonding using lithium disilicate laminates with three different luting agents (Variolink Veneer, RelyX U200, and RelyX Veneer). Then each agent was debonded using Er,Cr:YSGG laser (2.78 µm) using two different protocols:3.5 W, 48.14 J/cm2 , 20 Hz non-contact and 3.0 W, 48.14 J/cm2 , 20 Hz non-contact. The morphological, optical, and elemental analysis of enamel was performed before cementation and after laser debonding, using scanning electron microscopy (SEM), optical coherence tomography (OCT), and energy-dispersive X-ray spectroscopy (EDS). The level of statistical significance adopted was 5%. The EDS analysis of enamel after debonding revealed a significant increase in silane and carbon, as well as a decrease in calcium and phosphate contents. Analysis showed the presence of residual cement in most experimental groups but the morphological analysis showed alteration of the enamel's prisms only in the groups that used RelyX Veneer and Variolink Veneer cements. There was no evidence of deleterious morphological changes resulting from irradiation. However, an increase in the optical attenuation coefficient by the OCT was observed due to the presence of the remaining cement. It can be concluded that the Er,Cr:YSGG laser, in the mean powers used, is efficient for veneer removal without causing deleterious effects for the enamel.

Assuntos

RESUMO

Background: New applications in laser technology in aesthetic restorative dentistry merit further research. This study compares the debonding strength and failure mode of feldspathic ceramic veneers using either Er,Cr:YSGG (erbium,chromium:ytrrium-scandium-gallium-garnet) laser at two levels of fluency or no laser (control group). Methods: An in vitro comparative study was carried out using bovine teeth that were randomly distributed into 3 groups of 21 specimens each: (a) experimental group 1 (EG1): irradiated with Er,Cr:YSGG (Waterlase iPlus®; Biolase, Irvine) at an energy density per pulse of 4 J/cm2, using a handpiece (Turbo; Biolase) with a sapphire tip (MX7) and applying the beam perpendicular to the specimen at a distance of 4 mm for 60 sec; (b) experimental group 2 (EG2): irradiated as in EG1, but at 2.7 J/cm2; and (c) control group (CG): debonding without laser irradiation. Results: The stress required for veneer debonding was 8.19 MPa in CG, 0.91 MPa in EG1, and 0.48 MPa in EG2. The difference between the control and both experimental groups was statistically significant (p < 0.001). The percentages of adhesive failure were 40%, 61.9%, and 96%, respectively. Conclusions: Using the Er,Cr:YSGG laser at 4 or 2.7 J/cm2 requires significantly less force to debond ceramic veneers. The percentage of adhesive failures in the two experimental protocols was higher than in the control group. Application of the Er,Cr:YSGG laser using the parameters in this study may be useful in removing feldspathic ceramic veneers, avoiding damaging them and protecting the enamel.

Assuntos

RESUMO

Background: Laser irradiation modifies the topography and composition of dentin surface aiming to increase the retention of bonded posts. Objective: To assess the effect of dentin irradiation with Er,Cr:YSGG or diode lasers on the bond strength of fiber posts using self-adhesive resin cement. Materials and methods: Sixty bovine root canals were root-canal treated, post spaces were prepared, and subsequently fiber posts were cemented. The samples were distributed according to the surface treatment: distilled water (control), Er,Cr:YSGG (1.5 W, 20 sec), or diode (1.5 W, 20 sec) lasers. Bond strengths were assessed by pull-out (n = 10) or push-out testing (n = 10). Pearson's correlation was calculated. Failure mode after testing and the depth of tags in the dentinal tubules were analyzed by confocal laser microscopy. Data were submitted to analysis of variance and Tukey's test. A p < 0.05 was considered significant. Results: In the push-out test, Er,Cr:YSGG laser had significantly different higher values (5.43 ± 0.10 MPa) compared to the control (4.79 ± 0.05 MPa). Diode laser values were not significantly different from the other groups (5.12 ± 0.27 MPa). In the pull-out test, there were no significant differences between Er,Cr:YSGG (6.86 ± 2.16 MPa) and diode (8.43 ± 1.77 MPa) lasers, and both had significant differences compared to the control (4.18 ± 1.29 MPa). No correlation was found. Adhesive failures were predominant in all groups, and no significant differences in tag penetration among the groups were found. Conclusions: The Er,Cr:YSGG laser increases the bond strength of resin cement and fiber post to dentin in both tests, compared to control group without laser treatment. Diode laser only enhanced bonding for pull-out test.

Assuntos

RESUMO

Objective: The aim of this study is to assess the effect of Er,Cr:YSGG laser on the shear bond strength (SBS) and surface topography of two CAD/CAM ceramic materials bonded with self adhesive resin cement. Material and methods: sixty ceramic CAD/CAM discs were obtained, 30 lithium disilicate (IPS Emax) (Group LD), and 30 hybrid resin ceramic (Vita Enamic) (Group RC). The Slices were allocated into six groups (n=10) according to ceramic material and surface treatment; Group (LD-C): IPS Emax treated with 9% hydrofluoric acid (HF), Groups (LD-L1) and (LD-L2): IPS Emax treated with Er,Cr:YSGG, Group (RC-C): Vita Enamic treated with 9% hydrofluoric acid (HF), Groups (RC-L1) and (RC-L2): Vita Enamic treated with Er,Cr:YSGG laser. The laser parameters and irradiation protocol was 1.5 W (L1) and 2.5 W (L2). All samples were cemented with self-adhesive resin cement and thermocycled for 5000 cycles. The SBS was measured using a universal testing machine and the mean values (MPa) were analyzed using Two-way (ANOVA) (P ≤ 0.05) and Bonferroni's post-hoc test. Results: RC-C (16.55) showed highest SBS followed by LD-C (13.79), which revealed no statistically significant difference with RCP1 (12.33) and RC-P2 (11.2). The lowest SBS values were found with LD-P1 (2.7) and LDP2 (2.1). SEM analysis revealed Vita Enamic to have the highest surface roughness. Fracture pattern analysis showed adhesive failure with IPS Emax groups and mixed failure with Vita Enamic groups. Conclusion: Er,Cr:YSGG laser irradiation with the parameters used did not increase SBS of IPS Emax and Vita Enamic with composite resin compared to HF acid etching (AU)

Objetivo: O objetivo deste estudo é avaliar o efeito do laser Er,Cr:YSGG na resistência ao cisalhamento (SBS) e na topografia superficial de dois materiais cerâmicos CAD/CAM cimentados com cimento resinoso autoadesivo. Material e métodos: foram obtidos sessenta discos cerâmicos CAD/CAM, 30 de dissilicato de lítio (IPS Emax) (Grupo LD) e 30 de resina híbrida (Vita Enamic)(Grupo RC). Os discos foram alocados em seis grupos (n = 10), de acordo como material cerâmico e o tratamento de superfície; Grupo (LD-C): IPS Emaxtratado com ácido fluorídrico (HF) a 9%, Grupos (LD-L1) e (LD-L2): IPS Emaxtratado com Er,Cr:YSGG, Grupo (RC-C): Vita Enamic tratada com ácido fluorídrico (HF) a 9%, Grupos (RC-L1) e (RC-L2): Vita Enamic tratada com laser Er,Cr:YSGG. Os parâmetros do laser e o protocolo de irradiação foram de 1,5 W (L1) e 2,5 W (L2). Todas as amostras foram cimentadas com cimento resinoso autoadesivo e termocicladas por 5000 ciclos. A SBS foi medida usando uma máquina de ensaios universais e os valores médios (MPa) foram analisados usando (ANOVA) a dois fatores (P ≤ 0,05) e teste post-hoc de Bonferroni. Resultados: RC-C (16,55) apresentou maior SBS seguido por LD-C (13,79), que não revelou diferença estatisticamente significante com RCP1(12,33) e RC-P2 (11,2). Os menores valores de SBS foram encontrados comLD-P1 (2,7) e LD-P2 (2,1). A análise por MEV revelou que a Vita Enamic possui maior rugosidade de superfície. A análise do padrão de fratura mostrou falha adesiva nos grupos IPS Emax e falha mista nos grupos Vita Enamic. Conclusão: A irradiação com laser Er,Cr:YSGG com os parâmetros utilizados não aumentou a SBS de IPS Emax e Vita Enamic ao cimento resinoso em comparação com o condicionamento ácido com HF.(AU)

Assuntos

RESUMO

Objective: To evaluate the effect of the Er,Cr:YSGG laser on healing of critical-sized calvarial defects (CSDs) in rats submitted to inhalation of cigarette smoke. Background: Smoking has been implicated with the delay in the bone healing after osteotomy procedures, then the use of the Er,Cr:YSGG laser for osteotomy in smokers could be an alternative to the conventional drills. Methods: One hundred animals were randomly allocated into four groups: trephine-the CSDs were made with a trephine drill in healthy rats; Er,Cr:YSGG-the CSDs were made with the Er,Cr:YSGG laser in healthy rats; Trephine-S-the CSDs were made with a trephine drill in rats exposed to cigarette smoke; and Er,Cr:YSGG-S-the CSDs were made with the Er,Cr:YSGG laser in rats exposed to cigarette smoke. The inhalation of cigarette smoke started 7 days before the surgical procedure until euthanasia (immediately, 7, 15, 30, or 60 days after the surgical procedure). A histometric analysis and a histological description were performed to evaluate (1) the residual linear lengths and bone formation in the CSDs; (2) the quality of bone healing. Results: The use of Er,Cr:YSGG laser induces more bone formation compared with the trephine in smokers; however, the closure of the CSD was only superior in the Er,Cr:YSGG-S group compared to the Trephine-S group at the 60-day period. Conclusions: The use of the Er,Cr:YSGG laser stimulated the bone repair process after osteotomy procedures in animals submitted to exposure of inhalation of cigarette smoke.

Assuntos

RESUMO

OBJECTIVE: To evaluate the effect of Er,Cr:YSGG laser associated or not with acidulated phosphate fluoride (APF) on the control of enamel erosion progression. DESIGN: Enamel slabs (4 mm × 4 mm × 2 mm) from bovine incisors were flattened, polished, and received a tape on their test surfaces, leaving a 4 mm × 1 mm area exposed. Specimens were eroded (10 min in 1% citric acid solution) and randomly assigned into 8 experimental groups (n = 10): Control (no treatment); F (APF gel, 1.23% F, pH 3.6-3.9); Er,Cr:YSGG laser irradiation (P1: 0.25 W, 20 Hz, 2.8 J/cm2, 56 W/cm2); Er,Cr:YSGG laser irradiation (P2: 0.50 W, 20 Hz, 5.7 J/cm2, 1136 W/cm2); Er,Cr:YSGG laser irradiation (P3: 0.75 W, 20 Hz, 8.5 J/cm2, 1704 W/cm2); F + Laser P1; F + Laser P2; F + Laser P3. Specimens were then subjected to erosive cycling (5 min immersion in 0.3% citric acid solution, followed by immersion in artificial saliva for 60 min; 4×/day for 5 days). At the end of cycling, surface loss (SL, in µm) was determined with optical profilometry. Selected specimens were further evaluated by environmental scanning electron microscopy (n = 3). Data were analyzed using Kruskal-Wallis and Tukey tests (α = 0.05). RESULTS: Group F + Laser P2 had the lowest SL value, differing significantly from the control; however, with no significant difference from the other groups. All groups, except F + Laser P2, showed no significant difference in SL when compared with the control. An irregular and rough surface, suggestive of a melting action of laser, was observed on enamel in Laser P2 and F + Laser P2 groups. CONCLUSIONS: Association of the Er,Cr:YSGG laser in parameter 2 with fluoride was the only treatment capable of controlling the progression of enamel erosion.

Assuntos