RESUMO

The present study examined different concentrations of the butylated hydroxytoluene (BHT) inhibitor on the kinetics of conversion, polymerization shrinkage stress, and other correlated physicochemical properties of experimental resin composites (ERC). A model composite was formulated with 75 wt% filler containing 0.5 wt% camphorquinone and 1 wt% amine with BHT concentrations of 0.01 wt% (BHT-0.01); 0.1 wt% (BHT-0.1); 0.25 wt% (BHT-0.25); 0.5 wt% (BHT-0.5); 1 wt% (BHT-1), and control (no BHT). They were tested on polymerization shrinkage stress (PSS; n = 5), degree of conversion (DC; n = 3), maximum polymerization rate (RpMAX; n = 5), water sorption (Wsp; n = 0), and solubility (Wsl; n = 10), flexural strength (FS; n = 10), flexural modulus (FM; n = 10), Knoop microhardness (KH; n = 10), and microhardness reduction (HR; n = 10). Data concerning these tests were submitted to one-way ANOVA and Tukey's test (α = 0.05; ß = 0.2). BHT-0.25, BHT-0.5, and BHT-1 showed a gradually significant decrease in PSS (p = 0.037); however, BHT-1 demonstrated a decrease in the physicochemical properties tested. Thus, within the limitations of this study, it was possible to conclude that BHT concentrations between 0.25 and 0.5 wt% are optimal for reducing shrinkage stress without affecting other physicochemical properties of ERCs.

Assuntos

RESUMO

The research aimed to assess the effects of incorporating germinated Lupinus angustifolius flour into corn extrudates for different periods (3, 5, and 7 days), focusing on starch digestibility, morphological structure, thermal, and pasting properties. Extrudate with germinated lupinus flour for 7 days (EG7) significantly increased the content of slowly digestible starch up to 10.56% (p < 0.05). Crystallinity increased up to 20% in extrudates with germinated flour compared to extrudates with ungerminated flour (EUG), observing changes at the molecular level by FTIR that impact the thermal and pasting properties. X-ray diffraction revealed angles of 2θ = 11.31, 16.60, 19.91, and 33.04 as a result of the germination and extrusion processes. Microstructural analysis indicated starch-protein interactions influencing changes in calorimetry, viscosity, X-ray diffraction, and digestibility. PCA allowed establishing that the addition of germinated flours significantly affected the properties and microstructural characteristics of extruded products, potentially affecting digestibility and nutritional quality.

Assuntos

RESUMO

INTRODUCTION: The purpose of this study was to evaluate whether the mixing method of AH Plus Jet sealer affects its physicochemical and mechanical properties. METHODS: The properties of AH Plus Jet sealer were analyzed when mixed using either the Auto Mix Tip or manual mixing. The evaluated properties included radiopacity (n = 5), initial and final setting times (n = 5), flow (n = 5), and solubility (n = 3), following specifications outlined in ISO 6876/2012 and ADA Nº 57/2000. pH levels were measured at intervals of 3, 24, 72, and 168 hours (n = 10). The push-out bond strength test was conducted using a universal testing machine and using bovine teeth (n = 30). Failure modes were analyzed with stereomicroscopy. Porosity was evaluated under micro-CT (n = 5), and scanning electron microscopy was also performed (n = 5). One-way analysis of variance and Tukey, unpaired t-tests, or Mann-Whitney tests were used with a significance level of 5%. RESULTS: The Auto Mix exhibited a radiopacity value of 12.11 mmAl, whereas manual mixing resulted in 12.55 mmAl (P > .05). For initial and final setting times, Auto Mix showed 901 minutes and 1779 minutes, respectively, while manual mixing recorded values of 631 minutes and 1504 minutes (P < .05). In terms of flow, Auto Mix demonstrated higher values (25.26 mm) than manual mixing (21.71 mm) (P < .05). No statistical differences were observed between the two methods for solubility and pH (P > .05). Manual mixing presented a higher bond strength value (14.52 MPa) than Auto Mix (9.81 MPa) (P < .05). The mixed failure mode was the most frequent outcome for both methods. The highest porosity was observed for Auto Mix (P < .05). Scanning electron microscopy analysis revealed that manual mixing resulted in a smoother surface with fewer pores and smaller, more evenly distributed agglomerates compared to automatic mixing. CONCLUSION: The mixing method employed for AH Plus Jet sealer influences some physicochemical and mechanical properties of the material.

Assuntos

RESUMO

The impact of high-intensity ultrasound (HIU, 20 kHz) on the physicochemical and functional characteristics of gourd seed protein isolate (GoSPI) was studied. GoSPI was prepared from oil-free gourd seed flour through alkaline extraction (pH 11) and subsequent isoelectric precipitation (pH 4). The crude protein concentration of GoSPI ranged from 91.56 ± 0.17 % to 95.43 ± 0.18 %. Aqueous suspensions of GoSPI (1:3.5 w/v) were ultrasonicated at powers of 200, 400, and 600 W for 15 and 30 min. Glutelins (76.18 ± 0.15 %) were the major protein fraction in GoSPI. HIU decreased the moisture, ash, ether extract, and nitrogen-free extract contents and the hue angle, available water and a* and b* color parameters of the GoSPI in some treatments. The L* color parameter increased (7.70 %) after ultrasonication. HIU reduced the bulk density (52.63 %) and particle diameter (39.45 %), as confirmed by scanning electron microscopy, indicating that ultrasonication dissociated macromolecular aggregates in GoSPI. These structural changes enhanced the oil retention capacity and foam stability by up to 62.60 and 6.84 %, respectively, while the increases in the solvability, water retention capacity, and emulsifying activity index of GoSPI were 90.10, 19.80, and 43.34 %, respectively. The gelation, foaming capacity, and stability index of the emulsion showed no improvement due to HIU. HIU altered the secondary structure of GoSPI by decreasing the content of α-helices (49.66 %) and increasing the content of ß-sheets (52.00 %) and ß-turns (65.00 %). The electrophoretic profile of the GoSPI was not changed by HIU. The ultrasonicated GoSPI had greater functional attributes than those of the control GoSPI and could therefore be used as a functional food component.

RESUMO

In this study, the oils of açaí, passion fruit, pequi, and guava were submitted to physicochemical analysis to investigate their potential application in the food industry. Gas chromatography associated with mass spectroscopy showed that oleic and linoleic acids are mainly responsible for the nutritional quality of açaí, passion fruit, pequi, and guava oils, which exhibited 46.71%, 38.11%, 43.78%, and 35.69% of the former fatty acid, and 18.93%, 47.64%, 20.90%, and 44.72% of the latter, respectively. The atherogenicity index of the oils varied from 0.11 to 0.65, while the thrombogenicity index was 0.93 for açaí, 0.35 for guava, and 0.3 for passion fruit oils, but 1.39 for pequi oil, suggesting that the use of the first three oils may lead to a low incidence of coronary heart disease. Thermogravimetry showed that all tested oils were thermally stable above 180 °C; therefore, they can be considered resistant to cooking and frying temperatures. In general, the results of this study highlight possible applications of these oils in the food industry, either in natura or in typical food production processes.

RESUMO

Amaranth is a pseudocereal that contains between 50 and 60% starch, gluten-free protein, and essential amino acids. This study investigates the physicochemical changes in Amaranthus spp. grains, flour, isolated starch and nanocrystals during germination and malting. The moisture content increased from 8.9% to 41% over 2 h of soaking. The percentage of germination increased rapidly, reaching 96% after 60 h, a remarkable advantage over other cereals. The nutrient composition varied, including protein synthesis and lipid degradation. Lipid concentration decreased during malting, except for soaking, which increased by 62%. Scanning electron microscopy shows that germination does not cause morphological changes on the outer surface of the grains, while transmission electron microscopy indicates the presence of isolated nanocrystals with orthorhombic crystal structure confirmed by X-ray diffraction. The viscosity profile shows a decrease in peak viscosity. Therefore, amaranth is a potential pseudocereal that can be used as an additive in the production of fermented beverages.

Assuntos

RESUMO

In this study, the effect of different heating temperatures (80, 90, 100, and 121 °C) on the physicochemical and volatile flavor properties of fried mantles (Argentinian shortfin) was investigated. The squid mantles were soaked in a maltose syrup solution (20% w/v) for 10 s and fried in soybean oil for 10 s (160 °C), vacuum-packed, and processed at different temperatures for 10 min. Then, the squid mantles were subjected to colorimetric analysis, sensory evaluation, free amino acid analysis, and texture profile analysis. In addition, the volatile organic compounds (VOCs) in the squid mantles were analyzed. The results revealed that lower treating temperatures (80 and 90 °C) improved the chromatic and textural properties, along with organoleptic perception. Additionally, the content of amino acid in the squid mantles treated at 121 °C was significantly lower than that of the samples treated at other temperatures (p < 0.05). Headspace-gas chromatography-ion mobility spectrometry (HS-GC-IMS) was used to detect 41 VOCs, including their monomers and dimers. Among these detected VOCs, the contents of alcohols, ketones, and pyrazines were positively correlated with temperature. However, the content of aldehydes in the squid mantles gradually decreased as the heating temperature increased (p < 0.05). The combined HS-GC-IMS and E-nose results revealed that the lower temperatures (80 and 90 °C) were more suitable for flavor development and practical processing. This study provides valuable information for properly controlling the heating process of squid products, as well as flavor and practical applications for the aquatic industry.

RESUMO

The hard-shelled seed industry plays an important role in the global agricultural economy. In fact, only considering hazelnut and walnut, the global nut supply is over 5.6 tons. As a result considerable amounts are produced year by year, burnt or discarded as waste, bypassing a potential source of valuable compounds or features. This review deals with the recent scientific literature on their chemical composition as well as functional applications as an approach to sustain the utilization of the main byproduct derived from industry. Indeed, nutshells have received great interest due to their lignin, antioxidant, physical and mechanical features. It was found that these properties vary among cultivars and localities of plantation, influencing physical and structural features. The inconsistencies regarding the above-mentioned properties of nutshells lead to exploring the status of hazelnut and walnut shell applications in sustainable bio-economy chains. In fact, in terms of potential applications, the state of the art links their use to the construction industry and the manufacture of materials, such as resin or plastic composites, particleboards or construction panels, or vital infrastructure and as a filler in cement pavements. However, their current use continues bypassing their great antioxidant potential and their interesting chemical and mechanical features.

RESUMO

Corneal diseases represent a significant global health challenge, often resulting in blindness, for which penetrating keratoplasty is the clinical gold standard. However, in cases involving compromised ocular surfaces or graft failure, osteo-odonto keratoprosthesis (OOKP) emerges as a vital yet costly and complex alternative. Thus, there is an urgent need to introduce soft biomaterials that mimic the corneal tissue, considering its translation's physicochemical, biological, and economic costs. This study introduces a cross-linked mixture of economically viable biomaterials, including gelatin, chitosan, and poly-D-lysine, that mimic corneal properties. The physicochemical evaluation of certain mixtures, specifically gelatin, chitosan, and poly-D-lysine cross-linked with 0.10% glutaraldehyde, demonstrates that properties such as swelling, optical transmittance, and thermal degradation are comparable to those of native corneas. Additionally, constructs fabricated with poly-D-lysine exhibit good cytocompatibility with fibroblasts at 72 h. These findings suggest that low-cost biopolymers, particularly those incorporating poly-D-lysine, mimic specific corneal characteristics and have the potential to foster fibroblast survival. While further studies are required to reach a final corneal-mimicking solution, this study contributes to positioning low-cost reagents as possible alternatives to develop biomaterials with physicochemical properties like those of the human cornea.

RESUMO

Tara gum, a natural biopolymer extracted from Caesalpinia spinosa seeds, was investigated in this study. Wall materials were produced using spray drying, forced convection, and vacuum oven drying. In addition, a commercial sample obtained through mechanical methods and direct milling was used as a reference. The gums exhibited low moisture content (8.63% to 12.55%), water activity (0.37 to 0.41), bulk density (0.43 to 0.76 g/mL), and hygroscopicity (10.51% to 11.42%). This allows adequate physical and microbiological stability during storage. Polydisperse particles were obtained, ranging in size from 3.46 µm to 139.60 µm. Fourier transform infrared spectroscopy characterisation confirmed the polysaccharide nature of tara gum, primarily composed of galactomannans. Among the drying methods, spray drying produced the gum with the best physicochemical characteristics, including higher lightness, moderate stability, smaller particle size, and high glass transition temperature (141.69 °C). Regarding rheological properties, it demonstrated a non-Newtonian pseudoplastic behaviour that the power law could accurately describe. The apparent viscosity of the aqueous dispersions of the gum decreased with increasing temperature. In summary, the results establish the potential of tara gum as a wall material applicable in the food and pharmaceutical industries.