RESUMO

In this study, we address three key challenges in photonic crystals: modeling of isolated flat bands, electric field prediction, and band separation in dispersion relations. Using twisted square Bravais lattices at specific angles, we create Bravais-Moiré photonic crystals exhibiting unique characteristics. These include band pairing and parallelism in certain Brillouin zones, enabling predictable electric field behavior and identification of isolated, flat band pairs within extensive band gaps. We apply advanced Shape theory-based classification methods for precise band separation, offering significant contributions to photonics research and light manipulation applications.

RESUMO

Photonic crystals (PCs) are nanomaterials with photonic properties made up of periodically modulated dielectric materials that reflect light between a wavelength range located in the photonic band gap. Colloidal PCs (C-PC) have been proposed for several applications such as optical platforms for the formation of physical, chemical, and biological sensors based on a chromatic response to an external stimulus. In this work, a robust protocol for the elaboration of photonic crystals based on SiO2 particle (SP) deposition using the vertical lifting method was studied. A wide range of lifting speeds and particle suspension concentrations were investigated by evaluating the C-PC reflectance spectrum. Thinner and higher reflectance peaks were obtained with a decrease in the lifting speed and an increase in the SP concentrations up to certain values. Seven batches of twelve C-PCs employing a SP 3% suspension and a lifting speed of 0.28 µm/s were prepared to test the reproducibility of this method. Every C-PC fabricated in this assay has a wavelength peak in a range of 10 nm and a peak width lower than 90 nm. Inverse-opal polymeric films with a highly porous and interconnected morphology were obtained using the developed C-PC as a template. Overall, these results showed that reproducible colloidal crystals could be elaborated on a large scale with a simple apparatus in a short period, providing a step forward in the scale-up of the fabrication of photonic colloidal crystal and IO structures as those employed for the elaboration of photonic polymeric sensors.

RESUMO

We demonstrate, numerically, a new concept for on-chip magneto-optical (MO) modulation in dense wavelength division multiplexing (DWDM) applications. Our idea uses materials and mechanisms that are compatible with current silicon-on-insulator fabrication and CMOS technologies for monolithic integration. The physics behind our idea stems in the exploitation of the enhanced MO activity of a micro-ring, made of cerium substituted yttrium iron garnet (Ce:YIG) material, to actively manipulate the resonance wavelengths of an adjacent micro-ring resonator (MRR) of silicon (Si). This active manipulation of the latter MO-MRR structure is used to modulate the optical signal traveling through a side-coupled Si bus waveguide. Moreover, by proper tailoring multiple MO-MRRs (side-coupled to the single Si bus waveguide) to match wavelength channels in DWDM across the entire C-band optical communications spectrum, we extend our proposal to massive and dynamic MO modulation in DWDM applications. Significantly, we noticed that the active MO shifting of the resonant wavelength (used for MO modulation here) can be used for improvements in the spectrum utilization efficiency in future elastic optical networks (EONs).

RESUMO

In this work, we present an interferometric polymer-based electro-optical device, integrated with an embedded double-monolayer graphene capacitor for biosensing applications. An external voltage across the capacitor applies an electric field to the graphene layers modifying their surface charge density and the Fermi level position in these layers. This in turn changes the electro-optic properties of the graphene layers making absorption in the waveguide tunable with external voltages. Simultaneously, it is possible to appreciate that this phenomenon contributes to the maximization of the light-graphene interaction by evanescent wave in the sensing area. As a result, it is obtained large phase changes at the output of the interferometer, as a function of small variations in the refractive index in the cladding area, which significantly increasing the sensitivity of the device. The optimum interaction length obtained was 1.24 cm considering a cladding refractive index of 1.33. An absorption change of 129 dB/mm was demonstrated. This result combined with the photonic device based on polymer technology may enable a low-cost solution for biosensing applications in Point of Care (PoC) platform.

RESUMO

BACKGROUND: In vitro and in vivo testing of new technology was performed to evaluate the antiplasmodial activity of Photonic Multiphase Modulators (PMM) in cultures and in mice previously infected with Plasmodium falciparum and Plasmodium berghei parasites. METHODS: Cultures of P. falciparum infected-erythrocytes were exposed overnight to two generations of different APSE™ and BioPhoton-X™ PMM (C#1, R#1, R#2, D8 and D9). Growth of parasites was determined through flow cytometry or microscopy. Mice of the strain C57BL/6 were infected and treated with water exposed to second-generation APSE™ and BioPhoton-X™ PMM plus one previously untested first-generation PMM (AGN10). Parasitemia and weight loss were monitored throughout the infection until death or point of euthanasia was reached. After death, necropsy was performed on all animals and the number of days each survived was recorded. RESULTS: In vitro and in vivo testing using different APSE™- and BioPhoton-X™-designed PMM revealed an effect of D8 in lowering the growth of the parasite in vitro, while the best effect in mice was observed with D9 PMM, with a reduced weight loss and an increase in survival, although the results in lowering the parasitemia were inconclusive. D9 PMM did not generate ROS in vitro. CONCLUSIONS: APSE™ and BioPhoton-X™ optic circuit technologies can affect the growth of parasites and show protective effects in mice drinking from water treated with their PMM.

Assuntos

RESUMO

Porous silicon (PSi) on p++-type (111) silicon substrate has been fabricated by electronically etching method in hydrofluoric acid (HF) media from 5 to 110 mA/cm2 of anodizing current density. The problem of determining the optical properties of (111) PSi is board through implementing a photoacoustic (PA) technique coupled to an electrochemical cell for real-time monitoring of the formation of porous silicon thin films. PA amplitude allows the calculation of the real part of the films refractive index and porosity using the reflectance self-modulation due to the interference effect between the PSi film and the substrate that produces a periodic PA amplitude. The optical properties are studied from specular reflectance measurements fitted through genetic algorithms, transfer matrix method (TMM), and the effective medium theory, where the Maxwell Garnett (MG), Bruggeman (BR), and Looyenga (LLL) models were tested to determine the most suitable for pore geometry and compared with the in situ PA method. It was found that (111) PSi exhibit a branched pore geometry producing optical anisotropy and high scattering films.

RESUMO

Photonic materials featuring simultaneous iridescence and light emission are an attractive alternative for designing novel optical devices. The luminescence study of a new optical material that integrates light emission and iridescence through liquid crystal self-assembly of cellulose nanocrystal-template silica approach is herein presented. These materials containing Rhodamine 6G were obtained as freestanding composite films with a chiral nematic organization. The scanning electron microscopy confirms that the cellulose nanocrystal film structure comprises multi-domain Bragg reflectors and the optical properties of these films can be tuned through changes in the relative content of silica/cellulose nanocrystals. Moreover, the incorporation of the light-emitting compound allows a complementary control of the optical properties. Overall, such findings demonstrated that the photonic structure plays the role of direction-dependent inner-filter, causing selective suppression of the light emitted with angle-dependent detection.

RESUMO

Traditional cancer treatments, such as surgery, radiotherapy, and chemotherapy, are still the most effective clinical practice options. However, these treatments may display moderate to severe side effects caused by their low temporal or spatial resolution. In this sense, photonic nanomedicine therapies have been arising as an alternative to traditional cancer treatments since they display more control of temporal and spatial resolution, thereby yielding fewer side effects. In this work, we reviewed the challenge of current cancer treatments, using the PubMed and Web of Science database, focusing on the advances of three prominent therapies approached by photonic nanomedicine: (i) photothermal therapy; (ii) photodynamic therapy; (iii) photoresponsive drug delivery systems. These photonic nanomedicines act on the cancer cells through different mechanisms, such as hyperthermic effect and delivery of chemotherapeutics and species that cause oxidative stress. Furthermore, we covered the recent advances in materials science applied in photonic nanomedicine, highlighting the main classes of materials used in each therapy, their applications in the context of cancer treatment, as well as their advantages, limitations, and future perspectives. Finally, although some photonic nanomedicines are undergoing clinical trials, their effectiveness in cancer treatment have already been highlighted by pre-clinical studies.

RESUMO

A photonic sensor based on inversed opal molecular imprinted polymer (MIP) film to detect the presence of chlorantraniliprole (CHL) residue in tomatoes was developed. Acrylic acid was polymerized in the presence of CHL inside the structure of a colloidal crystal, followed by etching of the colloids and CHL elution. Colloidal crystals and MIP films were characterized by scanning electron microscopy and FT-IR, confirming the inner structure and chemical structure of the material. MIP films supported on polymethylmethacrylate (PMMA) slides were incubated in aqueous solutions of the pesticide and in blended tomato samples. The MIP sensor displayed shifts of the peak wavelength of the reflection spectra in the visible range when incubated in CHL concentrations between 0.5 and 10 µg L-1, while almost no peak displacement was observed for non-imprinted (NIP) films. Whole tomatoes were blended into a liquid and spiked with CHL; the sensor was able to detect CHL residues down to 0.5 µg kg-1, significantly below the tolerance level established by the US Environmental Protection Agency of 1.4 mg kg-1. Stable values were reached after about 30-min incubation in test samples. Control samples (unspiked processed tomatoes) produced peak shifts both in MIP and NIP films; however, this matrix effect did not affect the detection of CHL in the spiked samples. These promising results support the application of photonic MIP sensors as an economical and field-deployable screening tool for the detection of CHL in crops.

Assuntos

RESUMO

The aim of this work is to determine the varying dielectric constant of a biological nanostructured system via electrostatic force microscopy (EFM) and to show how this method is useful to study natural photonic crystals. We mapped the dielectric constant of the cross section of the posterior wing of the damselfly Chalcopteryx rutilans with nanometric resolution. We obtained structural information on its constitutive nanolayers and the absolute values of their dielectric constant. By relating the measured profile of the static dielectric constant to the profile of the refractive index in the visible range, combined with optical reflectance measurements and simulation, we were able to describe the origin of the strongly iridescent wing colors of this Amazonian rainforest damselfly. The method we demonstrate here should be useful for the study of other biological nanostructured systems.