RESUMO

Gasification is a thermochemical process that has gained significant interest in the field of biomass energy conversion. Despite the level of technological maturity of the process, the dynamic variation of the process as a result of changes in both the properties of the gasifying agent and biomass has not been analysed in sufficient depth. Therefore, the present study characterizes the process dynamically as a function of step-type changes in rice husk biomass moisture content and gasifying airflow. To identify stability conditions and the range for inducing disturbances, steady-state tests were carried out using a 32-factorial design. The experimental results demonstrate that within the tested range of airflow, the gasification process operates in the oxygen-limited zone. Despite increasing the airflow from 20 to 40 standard liters per minute (SLPM) and driving the reaction towards the combustion zone, the high temperatures achieved resulted in the gas reaching a peak Lower Heating Value (LHV) of 2.6 MJ/Nm3 and a gas power of 2.6 kW, with a Cold Gas Efficiency (CGE) of 62%. In contrast, the effect of biomass moisture content was negligible due to the thermal inertia of the reactor and the natural variation of the process. Dynamic evaluation revealed that the oxidation temperature and gas concentration were the variables that took the longest to return to stability after air disturbances. It took approximately 1200 s for the hydrogen (H2) concentration to stabilize, while the gas power required about 300 s. No clear results were observed regarding the impact of the dynamic disturbance in moisture content, which varied between 12.3% w.t and 21.5% w.t.

RESUMO

Due to their physical properties including high thermal stability, very low vapor pressure, and high microwave absorption, ionic liquids have attracted great attention as solvents for the synthesis of nanomaterials, being considered as greener alternatives to traditional solvents. While usual solvents often need additives like surfactants, polymers, or other ligands to avoid nanoparticle coalescence, some ionic liquids can stabilize nanoparticles in dispersion without any additive. In order to quantify how the ionic liquids can affect both the aggregation thermodynamics and kinetics, molecular dynamics simulations were performed to simulate the evolution of concentrated dispersions and to compute the potential of mean force between nanoparticles of both hydrophilic and hydrophobic natures in two imidazolium-based ionic liquids, which differ from each other by the length of the cation alkyl group. Depending on the nature of the nanoparticle, structured layers of the polar and apolar regions of the ionic liquid can be formed close to its surface, and those layers lead to activation barriers for dispersed particles to get in contact. If the alkyl group of the ionic liquid is long enough to lead to domain segregation between the ionic and apolar portions of the solvent, the layered structure around the particle becomes more structured and propagates several nanometers away from its surface. This leads to stronger barriers close to the contact and also multiple barriers at larger distances that result from the unfavorable superposition of solvent layers of opposing nature when the nanoparticles approach each other. Those long-range solvent-mediated forces not only provide kinetic stability to dispersions but also affect their dynamics and lead to a long-range ordering between dispersed particles that can be explored as a template for the synthesis of complex materials.

RESUMO

Understanding the strength behavior and leaching characteristics of mining tailings stabilized with alkali-activated cements in the short, medium, and long term is crucial for the feasibility of material applications. In this context, this study assessed the stabilization/solidification of iron ore tailings (IOT) using alkali-activated binder (AAB) composed of sugarcane bagasse ash and eggshell lime at curing times of 7, 28, 60, 90, 180, and 365 days. Additionally, leaching tests were conducted, along with the examination of possible changes in the chemical and mineralogical composition resulting from exposure to acidic environments. Tests included unconfined compression strength (UCS), leaching, X-ray diffraction, and Fourier-transform infrared spectroscopy for the IOT-AAB mixtures. The highest increase in UCS was observed between 7 and 60 days, reaching 6.47 MPa, with minimal variation thereafter. The AAB-bonded IOT exhibited no metal toxicity over time. Elements Ba, Mn, Pb, and Zn present in IOT and ash were encapsulated in the cemented matrix, with complete encapsulation of all metals observed from 90 days of curing time. The mineralogy of the stabilized/solidified tailings showed no changes resulting from leaching tests. Characteristic bands associated with the presence of N-A-S-H gel were identified in both pre-leaching and post-leaching samples for all curing times analyzed. Exposure to acidic environments altered bands related to carbonate bonds formed in the IOT-AAB mixture.

Assuntos

RESUMO

Aerosol emission by wind erosion in the arid and semi-arid areas of the world, is of environmental and health significance. Different methods have been used to mitigate aerosol emission among which the biological methods may be the most efficient ones. Although previously investigated, more research is essential to determine how the use of exopolysaccharide (biocrust)-producing cyanobacteria may affect soil physical properties. The objective was to investigate the effects of the cyanobacteria, Microcoleus vaginatus ATHK43 (identified and registered by the NCBI accession number MW433686), on soil physical properties of a sandy soil 15, 30, 60, and 90 d after inoculation. The effects of cyanobacterial biocrust on soil properties including shear strength, soil resistance, aggregate stability (mean weight diameter (MWD) and geometric mean diameter (GMD)), and wind erosion were determined in trays using a wind tunnel. Cyanobacterial inoculation significantly increased MWD (0-1 cm depth, from 0.12 mm to 0.47 mm) and GMD (from 0.3 to 0.5 mm) after a period of 90 d. Biocrust production significantly decreased soil erosion from 55.7 kgm- 2 to 0.3 kgm- 2 (wind rate of 50 kmh- 1), and from 116.42 kgm- 2 to 0.6 kgm- 2 (wind rate of 90 kmh- 1) after 90 d. In conclusion, cyanobacterial biocrust can significantly improve soil physical properties in different parts of the world including the deserts, and reduce aerosol emission by mitigating the destructive effects of wind erosion on soil physical properties.

Assuntos

RESUMO

Cow dung (CD) is a material that has been used for millennia by humanity as a stabilizer in earth building techniques in vernacular architecture. However, this stabilization has been little addressed scientifically. In this study, the effect of CD additions was assessed on earth mortars produced with one type of earth from Brazil and two other types from Portugal (from Monsaraz and Caparica). The effect of two volumetric proportions of CD additions were assessed: 10% and 20% of earth + sand. The German standard DIN 18947 was used to perform the physical and mechanical tests, and classify the mortars. In comparison to the reference mortars without CD, the additions reduced linear shrinkage and cracking. An increase in flexural and compressive strengths was not observed only in mortars produced with earth from Monsaraz. In mortars produced with the earth from Caparica, the addition of 10% of CD increased flexural strength by 15% and compressive strength by 34%. For mortars produced with the earth from Brazil, the addition of 10% of CD increased these mechanical strengths by 40%. The increase in adhesive strength and water resistance promoted by the CD additions was observed in mortars produced with all three types of earth. Applied on ceramic brick, the proportion of 10% of CD increased the adherence by 100% for the three types of earth. Applied on adobe, the same proportion of CD also increased it more than 50%. For the water immersion test, the CD additions made possible for the mortar specimens not to disintegrate after a 30 min immersion, with the 20% proportion being more efficient. The effects of the CD on mechanical performance, including adhesion, were more significant on the tropical earth mortars but the effects on water resistance were more significant on the Mediterranean earthen mortars. CD has shown its positive effects and potential for both tropical and Mediterranean earthen plasters and renders tested, justifying being further studied as an eco-efficient bio-stabilizer.

RESUMO

The impact of adding biogas waste (BW) to green waste (GW) composting to increase nitrogen supplementation and improve mature compost quality was investigated. Conducted over 90 days using static windrows, the experiment compared treatments with GW alone (T1) and GW supplemented with BW (T2 and T3). The results showed that the addition of BW increased temperatures, improved the C/N ratio, and expedited the stabilization process compared to T1. Furthermore, the addition of BW led to significant degradation of hemicellulose (up to 39.98%) and cellulose (up to 27.63%) compared to GW alone. Analysis of Fourier-transform infrared (FTIR) spectra revealed the presence of aromatic, phenolic, aliphatic, and polysaccharide structures in the compost, with BW supplementation enhancing these characteristics. Importantly, the germination index (GI) assessment indicated that the compounds produced were not toxic and instead exhibited stimulatory effects on seed germination. Overall, the findings suggest that supplementing GW composting with BW can enhance the quality and efficacy of the composting process, resulting in compost with desirable properties for agricultural use.

Assuntos

RESUMO

The bacterial composition of and the circulation of antimicrobial resistance genes (ARGs) in waste from Brazilian swine farms are still poorly understood. Considering that antimicrobial resistance (AMR) is one of the main threats to human, animal, and environmental health, the need to accurately assess the load of ARGs released into the environment is urgent. Therefore, this study aimed to characterize the microbiota in a swine farm in southern Brazil and the resistome in swine farm wastewater treated in a series of waste stabilization ponds (WSPs). Samples were collected from farm facilities and the surrounding environment, representing all levels of swine manure within the treatment system. Total metagenomic sequencing was performed on samples from WSPs, and 16S-rDNA sequencing was performed on all the collected samples. The results showed increased bacterial diversity in WSPs, characterized by the presence of Caldatribacteriota, Cloacimonadota, Desulfobacterota, Spirochaetota, Synergistota, and Verrucomicrobiota. Furthermore, resistance genes to tetracyclines, lincosamides, macrolides, rifamycin, phenicol, and genes conferring multidrug resistance were detected in WSPs samples. Interestingly, the most abundant ARG was linG, which confers resistance to the lincosamides. Notably, genes conferring macrolide (mphG and mefC) and rifamycin (rpoB_RIF) resistance appeared in greater numbers in the late WSPs. These drugs are among the high-priority antibiotic classes for human health. Moreover, certain mobile genetic elements (MGEs) were identified in the samples, notably tnpA, which was found in high abundance. These elements are of particular concern due to their potential to facilitate the dissemination of ARGs among bacteria. In summary, the results indicate that, in the studied farm, the swine manure treatment system could not eliminate ARGs and MGEs. Our results validate concerns about Brazil's swine production system. The misuse and overuse of antimicrobials during animal production must be avoided to mitigate AMR.

Assuntos

RESUMO

This study aimed to investigate the sustainable use of recycled plastics, specifically polypropylene (PP) and high-density polyethylene (HDPE), in the manufacture of geogrids for geotechnical and civil engineering applications. Plastics were collected from a recycling center, specifically targeting containers used for food, cleaning products, and other domestic packaging items. These plastics were sorted according to the Möbius triangle classification system, with HDPE (#2) and PP (#5) being the primary categories of interest. The research methodologically evaluates the mechanical properties of PP/HDPE (0/100, 25/75, 50/50, 75/25 and 100/0% w/w) composites through tensile and flexural tests, exploring various compositions and configurations of geogrids. The results highlight the superiority of pure recycled HDPE processed into 1.3 mm thick laminated yarns and hot air welded for 20 to 30 s, exhibiting a deformation exceeding 60% in comparison to the PP/HDPE composites. Through SolidWorks® Simulation, it was shown that the adoption of a trigonal geogrid geometry optimizes force distribution and tensile strength, significantly improving slope stabilization efficiency. Based on the results obtained, a laboratory-scale prototype geogrid was developed using an extrusion process. The results underscore the importance of careful composite design and yarn configuration selection to achieve the desired mechanical properties and performance in geogrid applications. It emphasizes the potential of recycled plastics as a viable and environmentally friendly solution for stabilizing slopes, contributing to the reduction in plastic waste and promoting sustainable construction practices.

RESUMO

The goal of this research was to create an antibacterial biopolymeric coating integrating lytic bacteriophages against Salmonella enterica for use in ripened cheese. Salmonella enterica is the main pathogen that contaminates food products and the food industry. The food sector still uses costly and non-selective decontamination and disease control methods. Therefore, it is necessary to look for novel pathogen biocontrol technologies. Bacteriophage-based biocontrol seems like a viable option in this situation. The results obtained show promise for food applications since the edible packaging developed (EdiPhage) was successful in maintaining lytic phage viability while preventing the contamination of foodstuff with the aforementioned bacterial pathogen.

RESUMO

Craniocervical tumors lead to cervical pain, instability, and neurological symptoms, reducing the quality of life. Effective surgical intervention at the craniocervical junction (CCJ) is critical and complex, involving comprehensive approaches and advanced reconstructive techniques. This study, conducted at Mexico City's National Institute of Cancerology, focused on three surgical cases that occurred in 2023 involving tumors at the CCJ: two chordomas and one prostate adenocarcinoma. We utilized a specialized technique: clivus-cervical stabilization reinforced with a polymethylmethacrylate (PMMA)-filled cervical mesh. Postoperatively, patients showed marked neurological recovery and reduced cervical pain, with enhanced Karnofsky and Eastern Cooperative Oncology Group (ECOG) scores indicating improved life quality. The surgical technique provided excellent exposure and effective tumor resection, utilizing PMMA-filled cervical mesh for stability. Tumoral lesions at the CCJ causing instability can be surgically treated through a transoral approach. This type of approach should be performed with precise indications to avoid complications associated with the procedure.