RESUMO

Microcystin, a cyanotoxin produced by Microcystis aeruginosa growing in eutrophic waters, can promote liver tumors in people ingesting contaminated water. To date, water treatment systems have not been effective in removing or degrading these cyanotoxins. In this work, we investigated the inhibitory activity of surfactants on the growth of M. aeruginosa and their application to extract the intracellular produced cyanotoxins. The experiments involving growth inhibition and extraction of cyanotoxins were carried out using the non-biodegradable surfactant cetyl trimethyl ammonium bromide (CTAB) in addition to other biodegradable surfactants. These were Tween 80 and surfactants derived from amino acids and peptides, respectively, from arginine, SDA, and hydrolyzed peptone, SDP. We demonstrated that the tested surfactants could be used to inhibit the growth of M. aeruginosa. At this point, CTAB and SDA proved to be the most competent surfactants in reducing cyanobacterial growth. Moreover, microcystins have been successfully removed from the water employing a cloud point extraction protocol based on the use of these surfactants and ammonium sulfate.

Assuntos

RESUMO

The complexity of aerodynamic particulate matter's (PM) matrices poses a challenge for the extraction and quantification of metals, especially for analytes with low concentration. Aiming to solve this issue, a precise and accurate protocol with the ultrasound extraction combined with microwave radiation digestion (USMW), was applied to PM samples with excellent compensations in sample throughput, digestion efficiency, and energy consumption. After the digestion and extraction procedures, the inorganic analytes, including rare earth elements, were determined by ICP OES. Two types of particulate matter sampled from two stations, Gobernacion (GOB10 and GOB2.5) and Milan (MIL10), corresponding to PM2.5 and PM10, were digested with a combination between HF, HNO3, and H3BO3. The absolute limits of detection ranged from 0.42 pg m-³ for V, to 3459 pg m-³ for As. The accuracy of the experimental study was assessed using two certified reference materials (CRMs), Coal Fly Ash (NIST1633b) and Fly Ash (BCR176). The method presented good accuracy, with recoveries ranging from 90 to 115%, except for Al (120%) and Fe (123%). Considering the replicates for the determination of analyte elements, the repeatability was below 10% for the relative standard deviation (RSD). A cloud point extraction (CPE) procedure, with parameters optimized for the determination of Pd and Pt, was successfully applied in digested PM samples with detection limits of 1.43 and 2.05 pg m-³ for Pd and Pt in MIL10 sample, respectively, and 76.6 pg m-³ for Pd and 110 pg m-³ for Pt, in samples GOB10 and GOB2.5, respectively.

RESUMO

A simple, novel and highly sensitive ionic liquid-assisted cloud point extraction (IL-CPE) and preconcentration method was developed for the determination and speciation analysis of tellurium, using 1-octyl-3-methylimidazolium chloride as an additive for improving the extraction efficiency of Triton X-114. The Te(IV) species was complexed with ammonium pyrrolidine dithiocarbamate, extracted into the micellar IL/surfactant phase and then directly measured by electrothermal atomic absorption spectrometry (ETAAS). The total Te concentration was obtained after a pre-reduction step and Te(VI) concentration was calculated as the difference between total Te and Te(IV). Several parameters, including the type and concentration of IL and surfactant, time and temperature of the IL-CPE procedure and ETAAS conditions were thoroughly evaluated and optimized. In addition, the action mechanism of the IL on CPE was studied by fluorescence measurements using Laurdan as a polarity probe. The decrease in the internal polarity caused by the incorporation of the IL into the micelles was responsible for the improvement in the extraction efficiency. Under the optimized conditions, a sensitivity enhancement factor of 87 and an extraction efficiency of 90% were achieved. Limits of detection of 1.1 and 1.7 ng L-1 and relative standard deviations of 3.9% and 5.0% for Te(IV) and Te(VI), respectively, were obtained. The developed IL-CPE method was successfully applied for Te speciation analysis in matrices of different complexities, such as waters (tap, underground and seawater), soil and sediment.

RESUMO

A method combining ultracentrifugation and cloud point extraction is proposed for the separation and determination of Fe, Ni and V porphyrins in crude oil. An emulsion containing about 200 mg of crude oil, 6% (w v-1) of Triton X-100™, 1.6% (v v-1) of chloroform and 0.1 mol L-1 of HCl was prepared. An aliquot (1.5 mL) of this emulsion was ultracentrifuged to separate the crude oil heavy fraction (asphaltene and particulate matter) and inorganic species, organometallic compounds and porphyrins of Fe, Ni and V remained in the supernatant. Another aliquot (1.5 mL) was heated up to 90 °C for 5 min to separate the porphyrins, both heavy and light organics compounds, light organic and particulate matter by cloud point extraction, only the inorganic and ionic organometallic compounds species remained in the aqueous phase. The supernatant and aqueous phase were analysed by simultaneous graphite furnace atomic absorption spectrometry. The concentration determined in the supernatant was subtracted from that determined in the aqueous phase, providing the quantification of Fe, Ni and V porphyrin in the crude sample. The accuracy of the proposed method was checked using SARA reference method. The elemental determinations in the fractions obtained using the proposed method and the comparison by SARA showed an absence of Fe in the aromatics and resins fractions. The results showed that about 40% of Ni and 70% of V in the crude oil sample are bounded to porphyrins.

RESUMO

Ultrasound-assisted extraction (UAE), cloud point extraction (CPE), and ultrasound back-extraction (UABE) techniques have been coupled for lixiviation, preconcentration, and cleanup of polybrominated diphenyl ethers (PBDEs) from milk samples for determination by gas chromatography-electron capture detection (GC-ECD). Physicochemical parameters that affect the efficiency of the extraction system were investigated using a design of experiments based on multivariate statistical tools, and considering the sample matrix along the development. The coupling of the leaching step, UAE, enhanced ca. 3.5 times the extraction efficiency of the former sample preparation methodology (CPE-UABE) leading to cleaner sample extracts suitable for GC analysis. Under optimum conditions, the proposed methodology exhibits successful performance in terms of linearity and precision, with recoveries in the range of 68-70% and LODs within the range 0.05-0.5 ng/g dry weight (d.w.). The proposed sample preparation methodology coupled three green analytical techniques. It expands the application frontiers of CPE for the analysis of biological samples by GC. The optimized methodology was used for determination of PBDEs in powder milk samples, from both commercial and human sources.

Assuntos

RESUMO

The characterization of inorganic elements in the produced water (PW) samples is a difficult task because of the complexity of the matrix. This work deals with a study of a methodology for dissolved Fe quantification in PW from oil industry by flame atomic absorption spectrometry (FAAS) after cloud point extraction (CPE). The procedure is based on the CPE using PAN as complexing agent and Triton X-114 as surfactant. The best conditions for Fe extraction parameters were studied using a Box-Behnken design. The proposed method presented a LOQ of 0.010µgmL-1 and LOD of 0.003µgmL-1. The precision of the method was evaluated in terms of repeatability, obtaining a coefficient of variation of 2.54%. The accuracy of the method was assessed by recovery experiments of Fe spiked that presented recovery of 103.28%. The method was applied with satisfactory performance to determine Fe by FAAS in PW samples.

Assuntos

RESUMO

Most of the procedures for antimony determination require time-consuming sample preparation (e.g. liquid-liquid extraction with organic solvents), which are harmful to the environment. Because of the high antimony toxicity, a rapid, sensitive and greener procedure for its determination becomes necessary. The goal of this work was to develop an analytical procedure exploiting for the first time the cloud point extraction on a lab-in-syringe flow system aiming at the spectrophotometric determination of antimony. The procedure was based on formation of an ion-pair between the antimony-iodide complex and H(+) followed by extraction with Triton X-114. The factorial design showed that the concentrations of ascorbic acid, H2SO4 and Triton X-114, as well as second and third order interactions were significant at the 95% confidence level. A Box-Behnken design was applied to obtain the response surfaces and to identify the critical values. System is robust at the 95% confidence level. A linear response was observed from 5 to 50 µg L(-1), described by the equation A=0.137+0.050C(Sb) (r=0.998). The detection limit (99.7% confidence level), the coefficient of variation (n=5; 15 µg L(-1)) and the sampling rate was estimated at 1.8 µg L(-1), 1.6% and 16 h(-1), respectively. The procedure allows quantification of antimony in the concentrations established by environmental legislation (6 µg L(-1)) and it was successfully applied to the determination of antimony in freshwater samples and antileishmanial drugs, yielding results in agreement with those obtained by HGFAAS at the 95% confidence level.

RESUMO

A highly sensitive and selective procedure for the determination of arsenate and total arsenic in food by electrothermal atomic absorption spectrometry after cloud point extraction (ETAAS/CPE) was developed. The procedure is based on the formation of a complex of As(V) ions with molybdate in the presence of 50.0 mmol L(-1) sulfuric acid. The complex was extracted into the surfactant-rich phase of 0.06% (w/v) Triton X-114. The variables affecting the complex formation, extraction and phase separation were optimized using factorial designs. Under the optimal conditions, the calibration graph was linear in the range of 0.05-10.0 µg L(-1). The detection and quantification limits were 10 and 33 ng L(-1), respectively and the corresponding value for the relative standard deviation for 10 replicates was below 5%. Recovery values of between 90.8% and 113.1% were obtained for spiked samples. The accuracy of the method was evaluated by comparison with the results obtained for the analysis of a rice flour sample (certified material IRMM-804) and no significant difference at the 95% confidence level was observed. The method was successfully applied to the determination of As(V) and total arsenic in rice samples.

Assuntos

RESUMO

An environmental friendly procedure was developed for fast melamine determination as an adulterant of protein content in milk. Triton X-114 was used for sample clean-up and as a fluorophore, whose fluorescence was quenched by the analyte. A linear response was observed from 1.0 to 6.0mgL(-1) melamine, described by the Stern-Volmer equation I°/I=(0.999±0.002)+(0.0165±0.004) CMEL (r=0.999). The detection limit was estimated at 0.8mgL(-1) (95% confidence level), which allows detecting as low as 320µg melamine in 100g of milk. Coefficients of variation (n=8) were estimated at 0.4% and 1.4% with and without melamine, respectively. Recoveries to melamine spiked to milk samples from 95% to 101% and similar slopes of calibration graphs obtained with and without milk indicated the absence of matrix effects. Results for different milk samples agreed with those obtained by high performance liquid chromatography at the 95% confidence level.

Assuntos

RESUMO

Novel strategies are proposed to circumvent the main drawbacks of flow-based cloud point extraction (CPE). The surfactant-rich phase (SRP) was directly retained into the optical path of the spectrophotometric cell, thus avoiding its dilution previously to the measurement and yielding higher sensitivity. Solenoid micro-pumps were exploited to improve mixing by the pulsed flow and also to modulate the flow-rate for retention and removal of the SRP, thus avoiding the elution step, often carried out with organic solvents. The heat released and the increase of the salt concentration provided by an on-line neutralization reaction were exploited to induce the cloud point without an external heating device. These innovations were demonstrated by the spectrophotometric determination of iron, yielding a linear response from 10 to 200 µg L(-1) with a coefficient of variation of 2.3% (n=7). Detection limit and sampling rate were estimated at 5 µg L(-1) (95% confidence level) and 26 samples per hour, respectively. The enrichment factor was 8.9 and the procedure consumed only 6 µg of TAN and 390 µg of Triton X-114 per determination. At the 95% confidence level, the results obtained for freshwater samples agreed with the reference procedure and those obtained for digests of bovine muscle, rice flour, brown bread and tort lobster agreed with the certified reference values. The proposed procedure thus shows advantages in relation to previously proposed approaches for flow-based CPE, being a fast and environmental friendly alternative for on-line separation and pre-concentration.